Search results

  1. B

    Yamaha RPM Guage

    It is most difficult for me to try and keep up with the many Yamaha differences. Can't imagine throwing Mercury and Evinrude into the mix.
  2. B

    Yamaha RPM Guage

    In a V150TLRC model the tachometer signal does not come from the voltage regulator. It comes from the CDI assembly. Via a green wire. That crosses several connectors before it makes it way to the tachometer. I would disconnect, inspect and reconnect all of the applicable connectors. See if...
  3. B

    Mercury / mariner - 60hp - 2 stroke - 1989 manual

    Some early Mariners were made by Yamaha. I was looking for the serial and some more information. What Yamaha calls the primary identification. Take a look at the CDI assembly and the carburetors and let me know what markings you see on them. For instance, the CDI assembly might have a 6H3 11 on...
  4. B

    Mercury / mariner - 60hp - 2 stroke - 1989 manual

    What is the complete engine ID?
  5. B

    2003 yamaha 150txrb oil pump linkage question

    Yes.
  6. B

    Yamaha 15 HP Motor.-

  7. B

    Question about LU rebuild + getting ripped off on sale.

    This is what I am seeing. breakfast wilmington nc
  8. B

    Question about LU rebuild + getting ripped off on sale.

    Make folks that want to help do extra work to provide that help.
  9. B

    Cooling Water Path through 2 Stroke Yamaha Outboard

    V6 four stroke water flow.
  10. B

    Cooling Water Path through 2 Stroke Yamaha Outboard

    There are as many different cooling water paths as there are Yamaha models. The paths are not the same. Here is the path for a 30 HP two stroke.
  11. B

    Hydraulic line

    Take the old one to a brake shop and see if they can fabricate a replacement. A bit fiddly but there are some crafty people out there.
  12. B

    Hydraulic line

    Certainly Yamaha ones.
  13. B

    Hydraulic line

    I would have no problem using a stain less steel flexible hose rated for the applicable pressure.
  14. B

    Tilt/trim solenoid/troubleshoot on 2003 50 2-stroke on pontoon boat

    The contacts within the relay can become intermittent. Work one time and then not work the next time. Why not do some trouble shooting to confirm the issue?
  15. B

    Tilt/trim solenoid/troubleshoot on 2003 50 2-stroke on pontoon boat

    There is an electric side of the unit and a hydraulic side of the unit. The relay provides electrical power to a electric motor that turns a hydraulic pump. A relay clicking typically has nothing to do with the amount of hydraulic fluid in the unit. A relay clicking and nothing happening tends...
  16. B

    2012 F20 Starts, But Putters Out Quickly

    Have you tried pumping the primer ball continuously when starting the motor to see if it will continue to run or not?
  17. B

    Yamaha 25MSHP Fuel Pump

    There is no fuel pump "kit". Part numbers are right where they always are. In the applicable Yamaha parts catalog.
  18. B

    Yamaha Motor swap- Same linkage?

    Same.
  19. B

    Yamaha 50TLR, 2 Stroke Choke Issue

    Here is how it works. Cold motor needs more gasoline to start. When the motor is cold the Primestart is cold also. When the Primestart is cold it provides more gasoline when in the automatic position. When the motor starts the lighting coil provides electrical power to the electrothermal valve...
  20. B

    Yamaha 50TLR, 2 Stroke Choke Issue

    With the red lever set to the automatic position, and the throttle handle in the idle position, if the motor does not start within several seconds of engaging the starter motor then something is amiss. More than likely the carburetor and the Primestart device need to be cleaned. And if by...
Top