Search results

  1. 9

    Aggravating gasket

    I have reused them many times before as long as they are not swollen/ out of shape when removed. e fuel does mess with them some times. there should not fuel high enough in the bowl to be in contact with them under normal running conditions. maybe when tilted up the fuel would come into...
  2. 9

    Engine flushing 150 yamaha

    just to let you know a muffler is something on a motor to quiet the exhaust out of a motor. muffs are for flushing an outboard that you attach to a lower unit on the water intake area. maybe Brits and Canada people call them mufflers for some reason. I am not sure if you are running the motor...
  3. 9

    TPS

    did you try brownspoint.com?
  4. 9

    Suzuki DT40 - not pumping water

  5. 9

    Suzuki 250AP trim switch question

    remove the hot wire. that should disable that switch
  6. 9

    Yamaha 01 250 OX66 running rough. Trying to figure it out.

    spark plugs maybe
  7. 9

    Yamaha problem

    have you tried pumping the primer bulb to see if the fuel bowls are full when this is happening? I guess this is a 2 stroke since you did not say it is a F50 I know this does not make much sense, but my BIL's 50 would bog down and die then giving it throttle and all I found wrong was some...
  8. 9

    Question about LU rebuild + getting ripped off on sale.

    or they tried pumping gear lub in without removing the top screw. causing pressure to build up inside and popping the seal out
  9. 9

    Question about LU rebuild + getting ripped off on sale.

    most people make it easy and post what motor they are taking about when they ask questions about it.. just because it may be one in a sig does not mean it is one of them
  10. 9

    Question about LU rebuild + getting ripped off on sale.

    what did you get for $20? I do not think you replaced all the seals and o rings for $20. Did you pressure check the lower to see where the leak was, and pressure check it after the repair to see it it is fixed?
  11. 9

    SUZUKI 1987 DT8

    why not try some air instead
  12. 9

    SUZUKI 1987 DT8

    where do you think you need to hook up fresh water to wash out / flush the motor? finding an owner's manual and service manual would be a good thing
  13. 9

    Yamaha 3hp 3MSHY (6L5) stalling after Carb Leak Fixed.

    just my thoughts, but it sounds like something plugged up or at least restricted the carb jets passages from opening them up
  14. 9

    Start pull cord

    as long as the flywheel is turning the drive shaft also turns, as the shaft is splined into the crankshaft. the water pump is on the drive shaft. prop shaft turns when in gear
  15. 9

    Replacing water pump seals 50HP TLRB

    have a look at #30 prices, $23.49 gets it all the housing by itself is $35, seals 6.75 each and Oring $5.40 I thought that was a miss print when I 1st ran into this on mine and you do not have to figure out how deep to seat the seals
  16. 9

    Replacing water pump seals 50HP TLRB

    if I remember correctly, I ran 2 sheetrock screws into it and pried on those screws to pull it out on my C40TLRX and then bought a new one. buying #30 gets you the housing, o ring, and both seals and is cheaper than buying them separately Oh yeah those are lower drive shaft seals not water...
  17. 9

    New Project Sunbird 170 Crosair

    still, he only asked for the specs for the boat, not for any motor. he is not someone that speaks English as a 1st language and that could be causing some of you problems understanding his posts
  18. 9

    New Project Sunbird 170 Crosair

    from the 1st post he was looking for the depth of the boat's gas tank which has no bearing on what motor it has mounted on it ", anybody knows the deep of the fuel tank? I want to buy a new fuel guage but need to be sure if the 7” or 9” works…"
  19. 9

    New Project Sunbird 170 Crosair

    What motor is hooked to the tank has no bearing on what that boat has for a fuel tank
  20. 9

    #2 / #5 Cylinders Not Firing

    yes the oil level switch in the main tank has more than one set of contacts, that send signals to the oil control module. looking at wiring does not mean it is good, need to be testing it your service manual has a lot of information in it. good to have if you are going to work on it yourself
Top