Search results

  1. alldodge

    Breakfast Dishes and Biscuits

    Have used crescent rolls and the bread to make a casserole kind of thing. Toss all kinds of things in with cheese and eggs comes out pretty good. Would really like a fool proof biscuit recipe, this guy keeps fooling it up. Can't get it to rise enough even with fresh flower and baking power
  2. alldodge

    Breakfast Dishes and Biscuits

    Thanks, have done oats many times, the frying pan bake sounds like a good one
  3. alldodge

    Help ID aftermarket sterndrive

    The number isn't under the top lid, separate the halves are find part numbers. Can determine age but not the gear ratio
  4. alldodge

    IAC Valve

    Another reason VP is the worst, great so long as it doesn't break. Cost is higher and when parts go NLA they remove the old part number so not even easy to find replacement. It may not be on the list of compatible because the part number was removed
  5. alldodge

    Bravo One U-Bolt

    It's a "U bolt"
  6. alldodge

    IAC Valve

    The GXI-J is listed as 3843750 The china one looks like the newer design GM My notes for Merc list Merc 805224A1 Walker 215-1026 BWD 21775 and Felpro gasket 17852 GM 17113598
  7. alldodge

    New impeller but now no cooling

    No such thing as a breaking the impeller loose, it either turns or it tears up. It's not the thermostat
  8. alldodge

    2008 Volvo Penta 5.0GXI-J High oil pressure

    Look low on port side of block where the remote oil filter attaches. This is where the oil pressure gauge sender and ECM oil pressure sensor should be
  9. alldodge

    ECM for 1999 Mercruiser MCM 5.0L EFI / 305 CID

    When placing the jumper on the DLC the rpm should increase and timing is set. Clamp down distributor, shut motor down and remove jumper. Start back up and watch timing, then see if timing advance increases as rpm does
  10. alldodge

    ECM for 1999 Mercruiser MCM 5.0L EFI / 305 CID

    Don't see it yet to be a ECM issue, but maybe a timing issue. Connect timing light and watch BTDC degrees and 8* and distributor is clamped down Shut motor down and remove jumper Restart motor and let idle Watch timing and increase rpm. Does it advance timing increase or stay the same?
  11. alldodge

    Alpha 1 Gen 1 trim Cylinder air Bleed Procedure

    Yes, that's it, just cycle up/down till all air is purged
  12. alldodge

    ECM for 1999 Mercruiser MCM 5.0L EFI / 305 CID

    Also are you using the correct tape for your size damper?
  13. alldodge

    ECM for 1999 Mercruiser MCM 5.0L EFI / 305 CID

    ok Your timing tape, when looking at the balancer, BTDC will be to the right of the center mrk and ATDC will be to the left
  14. alldodge

    ECM for 1999 Mercruiser MCM 5.0L EFI / 305 CID

    Does the rpm automatically increase to 1300 rpm when jumper is installed?
  15. alldodge

    Breakfast Dishes and Biscuits

    ok, What's the recipe ?
  16. alldodge

    Breakfast Dishes and Biscuits

    Most every Sunday morning I cook Breakfast, so I'm looking for new ideas for Two, can be for more but it's just us Make a lot of Garbage Eggs: Throw it diced/sliced potatoes, bell peppers, sausage/bacon, mushrooms, onion, other stuff Cook till Spuds are getting a bit crisp on edges, then stir...
  17. alldodge

    Help ID aftermarket sterndrive

    Most likely will have to separate to get the vintage. If it has a bolt on Vent plate to extend over the second prop then it's real old. If it has not bolt on extension and one anode it's newer If it has 2 anodes it's the newest style Compatibility chart shows which upper/lowers will swap with each
  18. alldodge

    IOS new prop

    Opinion: this is mine others will differ, just wait The motor does not have enough power to do what you want for the load placed on it. Reducing load by off loading folks and running with less weight works. To fix you either need more HP or less pitch prop. Reducing pitch from lets say 19P...
  19. alldodge

    2008 Volvo Penta 5.0GXI-J High oil pressure

    My guess is this is minimum oil pressure. Most list pressure should be 5 psi for every 1000 rpm, so 4K should show minimum of 20 psi, VP list 26. Having 65 to 75 is good. The gauge may be a bit off, and best way to verify is remove gauge sender and install hand held mechanical gauge
  20. alldodge

    Diacom engine parameters

    Hey @tpenfield how do you read hours with Diacom?
Top