Search results

  1. alldodge

    Orangish layer on boat will not come off

    Scotch Brite pads maybe
  2. alldodge

    Low fuel pressure, fuel filter half full while idling.

    The Reg that goes back to the filter is under the port side motor mount. There is a black plastic cover over the pump and Reg, Need to remove the cover so you can trace the line back to the filter The filter should have 3 lines on it. Rubber from the tank On top of the filter head there are...
  3. alldodge

    Mercruiser 502 (7.4l) turning over slowly, won't start.

    If it was left outside check oil level. If level is higher, water might have got in
  4. alldodge

    Mercruiser 502 (7.4l) turning over slowly, won't start.

    What is the history of the boat? Is it new to you, was it running fine prior?
  5. alldodge

    Volvo Penta Drive Belt - Lots of dust and quickly wearing??

    Have not heard of that happening, but then again I never tried running that size amps The fusion is 1400 watts 80A fuse recommended The Rockville is 3500 watts 80A fuse recommended
  6. alldodge

    How to actually BOOK a flight online?

    What happens when you go straight to the Airline?
  7. alldodge

    1989 Ranger 350V restore

    Fiberglass work is all so not fun
  8. alldodge

    How to remove Helm Lid

    Will be today or tomorrow. Adjusted the lift Thursday but now need longer bunk boards. The local lift guy said he will bring them today, but this is the same guy that I waited 3 years to get him to do another adjustment. I gave up and adjusted my self, then the next week he shows up, go...
  9. alldodge

    How to remove Helm Lid

    Don't know didn't ask Adding stuff to a new boat always takes place fire extinguisher, vhf, other things. Don't see any issue so long as what was added did not cause a problem, if it does it's my fault My Rinker has a lanyard but I stopped using it. I stood up beside the seat and killed the...
  10. alldodge

    How to remove Helm Lid

    Found it, Its VV 403 https://www.sbmar.com/wp-content/uploads/2018/03/VesselView403-Installation-Instructions.pdf
  11. alldodge

    How to remove Helm Lid

    Chap said to remove the bezel on the smartcraft gauge which will give access to screws hold gauge in. Once removed will have access to screws holding top. I'm looking for the install instructions for the gauge installed, it's square. I didn't get manuals for it so it's starting to take some...
  12. alldodge

    How to remove Helm Lid

    Your probably right, I'll try that
  13. alldodge

    How to remove Helm Lid

    No good Looking under the front lip I can find nothing In the head found a overhead panel which when removed showed nothing to help. It showed there is a full fiberglass wall between it and the top. I'm back to thinking there is some sort of spring latch I'm sure missing Formula :(
  14. alldodge

    Trim Manual

    Look in 14 for A1 G2
  15. alldodge

    Mercury 350 MPI beeping every few minutes

    Need to have the motor scanned for codes. Dealer or use Rinda https://www.rinda.com/
  16. alldodge

    Trim Manual

    About everyone of them
  17. alldodge

    Low fuel pressure, fuel filter half full while idling.

    Might be the regulator or the pump Could remove the return line coming from the Reg at the fuel filter head. Plug the filter head and hose end, then just key ON a couple times (do not start) to see if pressure builds above 40 psi. It should go close to 60 If it does increase, remove Regulator...
  18. alldodge

    How to remove Helm Lid

    I need to get behind it to install 1st Mate FOB kill switch
  19. alldodge

    How to remove Helm Lid

    Never thought there might be screws under the front lip, will have a closer look tomorrow
  20. alldodge

    How to remove Helm Lid

    Z-bracket? and don't see screws Just looked up Z bracket
Top