Search results

  1. T

    Gas leak while priming

    If the motor has been sitting for some time you could try tapping on the bowel to see if it will break free. But at the end of day it’s not the right thing to do. Your call.
  2. T

    1984 65 trim replacement

    There is a 92 60 on Craigslist Cape Cod. I’m not sure it’s what you need but it might be worth looking into.
  3. T

    Gas leak while priming

    My fingers were faster than my mind. Could also possibly be bad a gasket or warped bowel if they are the plastic type. Best
  4. T

    Gas leak while priming

    Possible a stuck needle on the float.
  5. T

    Popping and revving?

    I’m very curious. Can you explain inconsistent fuel pressure?
  6. T

    28hp super sea horse compatibility

    Lots of places to find parts with a little effort looking. Might even try here on I Boats. As always oem is best and Sierra is the next best thing for me.
  7. T

    Weird situation, looking for advice/how to repair

    Did they break off above or below the the block? Either way they can be removed. This is a pretty common thing to happen. Soak them with penetrating for awhile before doing anything. If above you maybe able to grab them with vise grips and try working them back and forth. Don’t try to spin...
  8. T

    Quit My Job . . .

    I did the same thing just yesterday. The only problem is I gave them a 10 month notice so who knows how this will really end. I have been at this job for 32 years and it’s time for a change. Wood working is my true passion and with a little luck will be my new gig.
  9. T

    Stay safe

    I hope all of you in Nova Scotia and the surrounding areas are safe from the wild fires and all turns out okay for you all. All the Best
  10. T

    98 evinrude DI 90hp

    First of all Thank You For Your Service. As for the motor do yourself a favor and unload it. I know several people that have spent loads of money on repairs and still were left stranded and looking for a tow back to the ramp just about every time they went out. There are a few lucky people out...
  11. T

    Popping and revving?

    The sea foam may have loosened up some crud.
  12. T

    Johnson 20 HP. Ignition Problem

    They have more like a flare to them rather a barb. The WD-40 will make them slippery and they will push right out.
  13. T

    Loss of power, won't plane

    There are all things that are best if used and not compromised with lower quality products if you don’t want to do it again. There are other ways around it but it will be a crap shoot. I have always used a wooden cradle and socket for pins with no problems. Best
  14. T

    Weird situation, looking for advice/how to repair

    Well that’s unfortunate but it doesn’t sound like the end of the world. I’m thinking with some TLC it would be salvageable.
  15. T

    Weird situation, looking for advice/how to repair

    Yes please let us know what happened.
  16. T

    Advice to remove the damage keyway

    Agreed work the ends one side then the other until it starts to pop up on one end. It’s a half moon in the crank so it will work it self out in theory. Best
  17. T

    Cut away....

    That is very kool
  18. T

    1989 Johnson 50hp won’t trim down

    I replaced one of those levers many years ago and it wasn’t cheap. I want to say it was around 60 or 70 bucks I had the part number written down on the wall and it’s still there. 0431962 was the number back in the day give a look and see what you find
  19. T

    1989 Johnson 50hp won’t trim down

    If you can grab the end of the cable where the lever is broken with a pair of pliers on pull on it it should lower.
  20. T

    Weird situation, looking for advice/how to repair

    Agreed on the broken magnets in the starter. If one is cracked it will try to spin but will lack any power.
Top