Search results

  1. alldodge

    Leak from "Lower/upper shoe"??? HELP!

    If its leaking from above then its coming from then most likely its coming from the drive shaft bellows. The above area is where the exhaust exits. The shift shaft goes up where the shift cable and drive shaft come together. If the bellows has oil in it then the upper drive shaft seal is...
  2. alldodge

    Solar Power Installation . . .

    The panel looks a bit larger for the Arch. Might think about another location, Maybe on the morning cover
  3. alldodge

    Mystery Engine Alarm

    I think the lights behind the Tach is just where they are positioned, doesn't mean anything. Would sure like to know what the code was the Mech read on the scanner. The impeller missing a blade was in need of replacement but getting the same alarm, it needs to be investigated further. Most...
  4. alldodge

    Mystery Engine Alarm

    Where do you see the numbers blinking? What motor 300-ca isn't enough serial numbers are best
  5. alldodge

    Intake warning sound for one second

    I'll assume its a Merc because its posted in the Merc section. Doesn't matter what the boat is but do need to know what motor and serial numbers are best? What is a intake warning sound? Maybe the alarm beeping?
  6. alldodge

    2002 5.0GL-B 305 Distributor

    It all deals with width of rotor and dizzy cap electrode width. While the 10 inch diameter damper outside circumference moves maybe an inch in one revolution to get 10* of advance. The rotor being half the diameter and moving 1/2 the distance (2 revs of the crank for one dizzy) needs to move...
  7. alldodge

    2002 5.0GL-B 305 Distributor

    Module and coil under rotor
  8. alldodge

    2002 5.0GL-B 305 Distributor

    We got the sound but no vid
  9. alldodge

    Serpentine belt replacement 4.3GXI-E

    If it looks good I wouldn't replace it. Keep the spare on the boat for piece of mind.
  10. alldodge

    Trailer bearings wear out ultra quickly.

    Speedy sleeves are not going to fix this issue, you need new axles. The sleeve needs to fit tight and from the looks of the old, its slipping. In most cases you would heat up the sleeve getting it pretty hot and use oven or welding gloves to put it on
  11. alldodge

    Bravo vs Bravo Diesel Transom Assembly?

    Differences https://www.perfprotech.com/blog/articles/mercruiser-transom-assemblies Some not all diesels use a bypass fitting (like 7.3). A plug is removed from the inside of the assembly and the fitting is installed. The bellows are the same for gas and diesel
  12. alldodge

    Trailer Shocks

    Once you have all the measurements they can be looked up https://www.shockwarehouse.com/news/pdf/kyb-shock-lengths.pdf
  13. alldodge

    Prop change rpm gain?

    Slip calculator Enter info you have and then the one you want to find leave it blank and elect that button. Can also do things like what would happen if this one thing was changed https://bblades.com/propeller-slip-calculator/
  14. alldodge

    2014 3.0 mpi want go over 2500 rpm’s we have Cleaned all injectors replaced distributor and idles fine just will not go over 2500 like it’s on a rev.

    Being it never run good the drive or prop may have been swapped out with one with to much pitch or higher ratio
  15. alldodge

    SPN 701 FMI 3 Check Engine Alarm

    Thanks @muc have it saved
  16. alldodge

    1999 mercrusier EFI 5.7 fuel pump not powering on

    Need a motor serial number to verify, but most EFI motors will not sound the alarm with the key left ON. The ECM grounds the other side of the alarm if it sees and issue. The carb motors would sound because the senders would ground the other side of the alarm. Back to the problem. With key...
  17. alldodge

    1994 indmar fi v8 good batt no crank

    There should also be a 20 amp fuse on the Red/Purple wire feeding the key switch. Should have 12V full time, doesn't matter if key is on or off
  18. alldodge

    1994 indmar fi v8 good batt no crank

    Bottom right in your pic is where the engine connector is. Also would think that is where the breaker is. Don't know if Indmar uses a 90 amp fuse on the starter post, but if it does that might be it. Looks like a cube
  19. alldodge

    Slave solenoid

    Using a slave solenoid(relay) just reduces the amount of current thru the key switch. It will work either way, but I do like using a relay
  20. alldodge

    02’ Volvo Penta 3.0L gsm-c Dash and fues wiring diagram

    1- Trim sender 4- Engine connector 6- Electric choke 10- Trim pump connector 11- Trim relays up/down 12- Trim pump 13- Temp switch 14- Fuse Trim 17- Start Assist Relay 18- Exhaust Temp overheat 19- Oil pressure sender 20- Low Oil pressure switch 21- Water Temp gauge sender 22- Buzzer/Alarm 23-...
Top