Search results

  1. S

    Ignition plate hold down evinrude 25 hp

    Yes, it does look older, and gunked up with black stuff.
  2. S

    Ignition plate hold down evinrude 25 hp

    Hard for me to tell from your pictures but are you missing part number 45?
  3. S

    1969 25 Hp Johnny Rude/Kicker?

    You want a service manual.
  4. S

    1969 25 Hp Johnny Rude/Kicker?

    HF When putting it in gear with the motor off you have to rotate the prop.
  5. S

    1969 25 Hp Johnny Rude/Kicker?

    You can idle down in nutruel so I do not understand. Something is blocking it from working correctly.
  6. S

    1994 Johnson 115hp, V4…Tilt Trim question?

    No, that's on the very low end. You could test with a different tester or test it after it's ran awhile. It might come up.
  7. S

    1969 25 Hp Johnny Rude/Kicker?

    Under the flywheel is the timing plate moving freely or is everything gunked up up there?
  8. S

    Yamaha runs awesome, will not re-start after running???

    Well you know how to start it when warm/hot now but now you need to know why you have to....more work to do
  9. S

    1969 25 Hp Johnny Rude/Kicker?

    Plus a jon boat doesn't have a lot of free board so you will want to be very careful. Precious cargo on board!
  10. S

    1969 25 Hp Johnny Rude/Kicker?

    Just to confirm, 16 ft boat correct? And what is your transom height? I'd stick with the 6, 7.5 or 8hp outboard. All the same size block. Best to try for an 80's or 1990's year so you don't have to mess with it as much. Post pictures of your boat and engine.
  11. S

    1970 4HP Johnson

    Get it running and then run some omc carbon guard through it.
  12. S

    2006 Johnson 9.9 four stroke J10EL4SD…

    Okay, yeah. I had to go look at your parts. They use a relay so the compounds things. I did find some stuff though. The link is to the remote start kit for your motor. Once I found the part on line I screen shotted the switch with the colors. Take a look...
  13. S

    2006 Johnson 9.9 four stroke J10EL4SD…

    Can you give me a picture of the starter soleniod or do they have it buried in a bunch of plastic stuff?
  14. S

    2006 Johnson 9.9 four stroke J10EL4SD…

    Yes, I know. What we need is a electric start tiller motor wiring diagram and we would be set.
  15. S

    2006 Johnson 9.9 four stroke J10EL4SD…

    Typically omc tach lead was brown so right now the colors aren't even jiving with me. I don't need wire end pictures I need pictures showing where the wires go to and then I might be able to make sense of it.
  16. S

    2006 Johnson 9.9 four stroke J10EL4SD…

    Tap my picture and look, rectifier should go to hot and you can see how the starter wires go....just need to wire in a switch to activate it. So that starts it and gives you the charge wire. Do you have any pictures of the motor showing wires, starter and such?
  17. S

    2006 Johnson 9.9 four stroke J10EL4SD…

    Yes, I get it... probably should hook the low oil cut out in as well.
  18. S

    2006 Johnson 9.9 four stroke J10EL4SD…

    Okay, well without a remote you will have to adlib some kind of harness, does your engine have a common lug lime this where all your hots go to? Understanding this is half or more of your battle.
  19. S

    2006 Johnson 9.9 four stroke J10EL4SD…

    Here is another with similar issue. Look at the wiring scem. Not in color but is this what your book shows? https://forums.iboats.com/threads/1997-johnson-9-9hp-4-stroke-wiring-diagram.730823/
  20. S

    Best way to free steering cable retainer nut stuck on tilt tube shaft

    Steering cables typically can fail two ways back by the motor. When you get it out, if you can, you can then determine if it's no good. I use Evinrude triple guard grease for stuff like that. If your lower unit has to come off than yes it might make it easier to move around. At the very least...
View older results
Top