Search results

  1. S

    1971 Evinrude fisherman, not pumping water

    Try unscrewing the threaded barbed adapter off the block for the pea tube and see if water blasts through there, otherwise remove thermo and then water jackets and head if needed. You could be plugged up.
  2. S

    Temperature alarm goes off as soon as you turn on the ignition.

    Assuming you still have your bro you might want to bleed out your oil lines coming from the tank.
  3. S

    Old Johnson 3hp

    You can clean it in place if it doesn't want to come out....carb spray cleaner and I use torch tip cleaners. Also, get a small spray bottle with 50 to 1 in it and when it begins to die squirt a little into the carb.
  4. S

    Old Johnson 3hp

    Just checking, you open the gas cap vent, correct?
  5. S

    Evinrude 9.5 vs 8hp speed test

    The 8 HP will move an 11 boat pretty fast once on a plane. Top end will be similar but out of the hole the 9.9 will be better. Block size, carb bigger on the 9.9 so it makes sense. If you fish and stuff the 8 is the motor to have
  6. S

    98 Johnson leaking hydraulic fluid.

    I said pump not motor....if motor spins than most likely it's fine. The whole rebuild kit is the way to go.
  7. S

    Assistance with 1984 8HP Evinrude

    Yes there is no adjustment on the outboard. Look to see if something is blocking the shifter handle otherwise your reverse gear may be shot. Used lower units are a dime a dozen for that model. To remove, just undo the 3 lower bolts and slide the unit down and off. If it doesn't want to come...
  8. S

    Please help, no spark and so lost

    Sounds like you already disabled the kill. (Removed two wires) The coil under the fly is all there is left to do.
  9. S

    Please help, no spark and so lost

    It doesn't matter....cutting one wire will disable it. Are the coils grounded? If yes then you will need to test the components under the flywheel.
  10. S

    Please help, no spark and so lost

    Unplug or cut the kill switch wire then test.
  11. S

    Rectifier question for 1984 Evinrude E140TLCRD

    For models with trim and tilt. Test yours first with a multimeter.....easy to do.
  12. S

    1990 70hp Evinrude Temp Sensor

    Here the link to your parts numbers....unavailable but you may find some on eBay or something. https://www.marineengine.com/parts/johnson-evinrude-accessories/index.php?year=1990&model=Instruments+1990&section=Outboard+Water+Temperature+Gauge+Kits&yid=34096&mid=34099&sid=38124
  13. S

    1978 Evinrude 140 V4 Only firing on 2 cylinders

    With all that corrosion it could be a wire but after cleaning up the wiring swap the coils from one side to the other and see if your problem follows. Your boat looks fast!
  14. S

    Evinrude 1987 E50BELCUD Idle Performance and Timing Question

    I would say put the vro pump back on and that would reduce oil consumption at idle and solve your problems.
  15. S

    Old Johnson 3hp

    High speed jet? Fuel pump? Onboard tank or auxiliary?
  16. S

    98 Johnson leaking hydraulic fluid.

    You don't need a manual for that....they all work the same. Believe it or not the pumps do burn out. Find a used one or replace the pump.
  17. S

    2000 90hp Johnson no spark

    Check to make sure your control box is in nutruel. Giggle the handle. Man overboard switch. Key switch Malfunction to name a few.
  18. S

    98 Johnson leaking hydraulic fluid.

    That with the trim button? Looks plenty high.
  19. S

    Mandatory kill switch for a Evinrude 9.9 Evinrude installation and testing

    I put one of these on a Johnson 25 recently and it worked fine. No idea how long it will last.
Top