Search results

  1. nola mike

    Chattering in out drive

    Definitely. How about the Merc tools? Did you do the gear housing as well?
  2. nola mike

    Over heating 1988 mercruiser 185 4.3

    Which diagram? There are 2 I posted
  3. nola mike

    2007 Merc 5.0 TKS stalled at speed, had to be towed

    Fill your tank. No way a 5.0 is getting 2 gal/hr. Edit: was your separator filter dry or have gas in it? As mentioned you have an electric pump after the filter, it shouldn't run unless engine is cranking or running
  4. nola mike

    Over heating 1988 mercruiser 185 4.3

    What's your serial #? An '88 should be Merc manual #7. Your diagram doesn't look right... Was it overheating prior to your work? Try running it on muffs and not in a bucket, and verify your temps with an IR gun. This is the correct area to post.
  5. nola mike

    Chattering in out drive

    How did you manage that? Which gears needed replacing? No Merc special tools? Last I looked each gear set was multiple 100's...
  6. nola mike

    Chattering in out drive

    So curious as to what the total parts cost was, including tools?
  7. nola mike

    The ole rope in the prop

    https://forums.iboats.com/threads/how-to-troubleshooting-your-engines-starting-system.166663/
  8. nola mike

    1995 5.7 Mercruiser no start, no fire.

    Nice. How'd you find it?
  9. nola mike

    Heat Exchanger blocked: recommendations how to flush or unclog?

    He said he's got a 170, which is the 1985/86 3.7l. paired with an a1g1 and full OEM closed cooling. Only pump is in the drive, as mentioned.
  10. nola mike

    Mercruiser 170 - Spark at distributor, not plugs

    Spark plug/coil wire, plugs, cap, rotor are the only possible failure points. If you're not getting spark at any plug, I'd guess that the issue is at the rotor button connecting to the cap (I read this as having spark off the coil wire)
  11. nola mike

    2010 4.3L TKS Thunderbolt Ignition Troubleshooting

    The Sierra ones are good, and I've seen a couple of other decent ones. Good ones have a plastic coated inner sheath, pretty obvious if it's quality or not. Electronics, who knows, rubber who knows.
  12. nola mike

    Alignment question chasing the marks or slide the tool

    The whole point of the tool is to make sure that there isn't stress on the coupler. If it slides easily, you've confirmed that you're not stressing the coupler. I think the witness marks are secondary, to be used to figure out how to move the engine when the tool won't move freely
  13. nola mike

    2010 4.3L TKS Thunderbolt Ignition Troubleshooting

    Op confirmed that he's having a spark issue. Can't think of a tks failure that would do that...
  14. nola mike

    2010 4.3L TKS Thunderbolt Ignition Troubleshooting

    As mentioned, if your spark test at the coil is consistently good, the failure can only be in the ignition sensor or in the cap/rotor/wires, or wiring to the sensor. If it's intermittent, then all bets off. Edit: Also, wouldn't expect an intermittent issue with the sensor itself unless it's the...
  15. nola mike

    2010 4.3L TKS Thunderbolt Ignition Troubleshooting

    Glad it's working but I don't think that's your problem. If either the tach or SIS is grounded you won't get spark from the coil during the TB troubleshooting test.
  16. nola mike

    2010 4.3L TKS Thunderbolt Ignition Troubleshooting

    Might also try that last test on the plug wires (or at least 1 with the rotor lined up). Your problem could be coming from the rotor/cap/plug wires as well as the sensor (which it still sounds like)
  17. nola mike

    Exhaust flapper fell down in the exhaust tube

    Dremel on a string?
  18. nola mike

    alpha one w/485 srt 4cyl alinement issue

    That's correct
  19. nola mike

    Early EZ Shift outdrive questions

    I think real old drives had a different number of splines in addition to a different length drive shaft. Shouldn't be an issue if swapping the shafts though. I did think that the cutouts were different sizes for some reason. And also, was OP hoping to keep inner transom plate or swap the whole...
  20. nola mike

    Exhaust flapper fell down in the exhaust tube

    Flappers can supposedly wear a hole in the y pipe over time, though I'm not sure if it's the flapper itself or the pin that does the damage. Good ideas about trying to reach it from the drive side
Top