Search results

  1. R

    Proper oil level for 60hp Bigfoot

    Often the filler is separate from dipstick.----Get your dealer to show you how to check the oil.
  2. R

    would a johnson 1978 200 hp tilt trim setup work on a 1976 johnson 200 hp motor

    Red is power from battery to the switch.-----Blue is for up.----Green is for down.-----Start a new thread and post pictures of what you have.-----Model # of your motor ?
  3. R

    timing???

    Note ---Timing on these motors does not normally go out of adjustment.-----Maximum timing advance is set at the factory for the life of the motor.-----Actual timing when engines idles does not matter.-----Make absolutely sure that you understand what " idle timing " means on this 2 stroke...
  4. R

    1991 mercury 115hp 2 stroke gauges?

    Explain the type of oil gauge you want.-----Is there not an oil level gauge on the cowling ?
  5. R

    Evinrude Mariner 6 HP 1965 Model 6502, 6503 3 fin prop

    Step #1 is to identify CLEARLY what you have.----Perhaps a newer lower unit has been fitted.-----Does your prop have a slip clutch ( rubber ) in it?----Is the prop cap rubber or screw on plastic.----Is the hole for the shear pin near the oil seal or near the prop cap.-----I do not believe 1965...
  6. R

    Mercury 40 not starting

    Stop cranking and cranking , it is easy to destroy the starter.----Do some testing.----Post the actual compression numbers.-----Oil injection system tested and working properly.----Serial # of your motor.
  7. R

    Crack in splash well

    I would be very concerned.-----What kind of boat ?----Any more pictures ?---Possible weak / rotted transom.
  8. R

    Will it Work? - Joe Reeves Timing Method

    Ignore / delete post #2.----No idea how it was posted in the wrong thread.
  9. R

    90hp Mariner doesn’t start

    Correct.----And you crank for a few seconds till gauge stops going up.----You will likely get at 5 of 6 cylinders.---Test the spark at the same time.----And throttle dos NOT need to be open.
  10. R

    90hp Mariner doesn’t start

    When the motor does it's ---" want to start " ---routine the spinning flywheel kicks the bendix down.----Some will argue but.-----It is up to you to determine the following.-----Proper cranking speed to get spark that jumps a gap of 3/8" , yes or no ?----Battery in good condition and load tested...
  11. R

    Evinrude 25 Project - Rocky Start

    A manual is not in the cards ?----A manual will save you lots of beer tokens , and blisters on your fingers , cuts and bruises.---Sleepless night too.
  12. R

    28hp super sea horse compatibility

    Fairly familiar ??----I started working at a Johnson dealer in 1968 !----It was an everyday motor at that time.----Today I have a bunch of that type of motor for parts.----Know them inside out !
  13. R

    Will it Work? - Joe Reeves Timing Method

    Many storage yards now require " minimum or no fuel "------No batteries in place or hooked up.-----Never mind when folks want to store an EV of some sort.-----It is becoming scarier every year.
  14. R

    Burned boat and insurance offer

    Insurance companies have people on a " bonus system "------They get a bonus if they save the company money on settlements.-----If you have documentation / pictures to demonstrate the value , you might want somebody to give you an opinion.
  15. R

    Motor revs up but doesn’t go anywhere?

    It is NOT odd.----That is the way most outboards are made !
  16. R

    1954 cd11 johnson wont run

    There are lots of fuel pumps that can be adapted for that motor.----One from a 1968 3 HP to some 2000 model year of Johnon will work.----A 3 to 25 HP used that little square pump !
  17. R

    1975 Johnson stinger 75 hp

    Check item # 40.-----And 120 PSI is low for that motor.----Yes it is.----So test with a gauge.----Or remove cylinder head for a look.-----Head gasket is cheap.
  18. R

    1954 cd11 johnson wont run

    I think the pressure tank is very good and reliable !!
  19. R

    '87 Scarab 21

    Pottahawk point ?
  20. R

    1975 Johnson stinger 75 hp

    You meant to say with CHOKE closed it will run and then when you open choke flappers it stalls ? ---I think that means you need to revisit carburetor work.----Find the high speed jets ( orifice plugs ) in the carburetor bowls.---And what are the actual compression values.-----You can help...
Top