Search results

  1. alldodge

    91 bayliner 5.0 mercruiser dies shifting to reverse

    Might need a lower shift cable replacement, but do need the shift interruptor adjusted. Go thru the adjust procedure
  2. alldodge

    Inconsistent bogging/acceleration until it hit around 20mph - Mercruiser 5.7l

    We're going to have to go at this like they messed everything up. A clicking could be lifters but this would not need a head gasket. Get a lianer compression gage from a auto parts store. Disconnect the coil, open throttle to wide open and do a compression test
  3. alldodge

    Mercruiser 5.7 V8 (1997) jumping RPM

    Howdy Manuel Need your motor serial number? Assuming your watching the boat Tachometer change rpm. Unless your hearing the motor change rpm alog with watching the Tach it may just be a Tach issue and not the motor. If you have TBV then the wire needs to go to ground to set timing. If you...
  4. alldodge

    Tahoe deckboat sink fuse is blowing

    Look at the pump it should have the amps listed on it. If not get the model number and look up the specs
  5. alldodge

    SX cobra out drive crack

    Doesn't look like a crack, looks like someone used a screw driver to separate the drive at one time. You should be ok. That said, the drive should be removed at least every couple season to check motor alignment
  6. alldodge

    Overheating

    How many hoses go into the connection? If more then 2, where do they come from? Where do the thermostat hoses connect?
  7. alldodge

    Inconsistent bogging/acceleration until it hit around 20mph - Mercruiser 5.7l

    It never ran right since the head gasket was replaced. The other issues that keep coming I'm wondering just what the mechanics have "actually" done. All things listed while time consuming are not hard, and if done correctly there should be no issues running again. Did the motor over heat...
  8. alldodge

    transom replacement Chrysler

    Use CSM (chop stran mat) with polyester resin. Using 2 pieces of 3/4 plywood and bond the 2 together using CSM and resin Some use corebond to bond the wood to the transom prior to covering and tabbing with CSM. Some just mix a thick resin and CSM to bond plywood to transom (what I did)
  9. alldodge

    Perko switch question (1 engine 2 battery)

    Yes I understood what you had when replying Someone replaced the cables with incorrect ones and this is the reason no one on you tube talks about them
  10. alldodge

    Perko switch question (1 engine 2 battery)

    Best to have ring terminals on Bat cables on a boat. Terminals should be crimped and then sealed. No soldering because if cable gets hot it could melt the solder and pull out Below uses an ACR
  11. alldodge

    Inconsistent bogging/acceleration until it hit around 20mph - Mercruiser 5.7l

    You need a new mechanic Don't see bogging being the fuel pump, the carb either has enough fuel or it doesn't. Checking fuel pressure can always be good to know, but I would suspect carb Heads been removed twice so things could have gone wrong. Hope the head was checked for flatness prior to...
  12. alldodge

    Overheating

    The HE doesn't look like the typical Merc design. The older design used 2 hoses coming in from the Thermostat housing to the front of the mans and 2 others coming back from the rear of the mans. I'm seeing what appears to be 3 hoses (maybe more) connecting to the top tank
  13. alldodge

    Overheating

    With the overflow filling I wonder if you have a blown head gasket Post some pics of the motor hose routing to help me understand how its connected. I'm looking at manual 2 and want to compare
  14. alldodge

    2003 Mercruiser 350 Mag MPI - No start

    The HVS dizzy has a "very small" spot where it will fire correctly. Original versions of the ECM it could be moved about an 1/8 either side if the motor was experiencing a misfire. There is a bulletin out for this and another of how to get it exact. The dizzy also has a reluctor wheel (your...
  15. alldodge

    Mercruiser 3.0 Delco EST ignition module hell

    Don't know for sure but my thought is there is a lot of junk parts out there. Anyone can print up a dox and label making it look like the real thing. I got some crap parts from rockauto that said genuine GM for the car. After taking car to the dealer, they replaced the same part and now it...
  16. alldodge

    1988 Rogue 2420

    ok, then its the design engineers fault
  17. alldodge

    Alpha One Gen II loosing oil

    Then most likely you have a shaft leak, no guarantees
  18. alldodge

    1988 Rogue 2420

    That's good to hear Have U tried one of these to get filters off? https://www.amazon.com/Neiko-03421A-Auto-Adjustable-Filter-Adaptor/dp/B000UD0CTQ
  19. alldodge

    Mercruiser 165 riser elbow plug

    Another idea If u have a Sawzall with short blade. Drill hole and use Sawzall to cut several places and can use a chisel to knock pieces out
  20. alldodge

    Mercruiser 165 riser elbow plug

    Might think about drilling small holes in 4 corners maybe 3/16. Look and determine what would work best. The use a large bit to connect the holes. Basically trying to mak it square thru hole. Use a file, drimmel or other to square it off. See if drive can be inserted. Not heat it up slowly...
Top