Search results

  1. Faztbullet

    1988 Johnson 70hp inspection

    You have the bridged port exhaust and these engines are prone when water pumps get weak the bridge expands and scuffs the exhaust side of piston, You will find when you tear it down piston may have a a small oil hole for bridge. The replacement pistons will not. I drill them in piston to oil...
  2. Faztbullet

    1998 Johnson J115ELECM idle adjustment help!

    You have to ground the wht/blk wire from pack to disable QS, just unplugging does nothing. Some packs will go into QS with it bypassed but couple of quick blimps of throttle over 1500rpm will kicker out
  3. Faztbullet

    Flywheel magnets

    Pretty sure 4 magnet was for AC lighting. Will work on both
  4. Faztbullet

    Help with Johnson 150 Pinion Bearing Removal

    If leaking by o-ring and its not damaged the housing likely warped. That may be why it took a dump from intrusion
  5. Faztbullet

    2 Cylinder Johnson 40hp Old Trim/Tilt

    Go to a hydraulic shop and but the nylon and rubber o-rings and wipers
  6. Faztbullet

    150 mariner

    Are you trimmed all the way down starting off?
  7. Faztbullet

    Help with Johnson 150 Pinion Bearing Removal

    Did you replace pinion bearing as it was shot
  8. Faztbullet

    1969 85hp Evinrude, CDI Box squeal sometimes?

    Normal
  9. Faztbullet

    Black scuff marks on cylinder walls

    Looks like it scuffed walls and someone honed over the damage and reringed.. a " Bubba" fix. It been punched .030 over sometime in its life.
  10. Faztbullet

    Ruh-Roh… a new gear case may be in order

    You will likely have to swap driveshaft as its fine spline. Most of the 60-70hp 3 cylinder where 4 spline. If you swap shafts you will need to reshim pinion
  11. Faztbullet

    Ruh-Roh… a new gear case may be in order

    Call your insurance company and get a new OEM
  12. Faztbullet

    Help with Johnson 150 Pinion Bearing Removal

    If it chit the pinion for no reason (I dont really see the water evidence) the gearcase may be warped. There is a gearcase alignment tool to check this. I will not rebuild a gearcase unless it is checked. I have discarded cases that look almost new that was warped. If not it will chit the gear...
  13. Faztbullet

    Cost of carb rebuild

    To the original poster.....I charge $95 per carb plus parts. This is removal/install/sonic clean/sync and link. Fuel pump is $95 plus parts. Part would be 4 carb kits @$15.85x4, 4 inlet needles @$11.50 and pump @$31.49 and $16.00 for shop supplies such as fuel ties/carb spray
  14. Faztbullet

    Help identifying fitting. 2000 225

    That fitting gets a cap and zip tie
  15. Faztbullet

    Overide spring ?

    Choke flap spring...prevents flaps from closing at WOT
  16. Faztbullet

    2000 Johnson 70 j70plsis

    Someone cut that or came from factory like that. Sleeves are installed/straightened and block is drilled in middle of transfer port webbing. It is only drilled deep enough to dimple the sleeve and a set screw is installed and epoxied over
  17. Faztbullet

    2000 Johnson 70 j70plsis

    Needs a new sleeve and all sleeves pinned in placed
  18. Faztbullet

    Water in my oil

    Are you running FC rated oil?
  19. Faztbullet

    Water in my oil

    Thats engine oil. Make sure the t-stat is working correctly
  20. Faztbullet

    Recommended DVA meter or DVA adapter for a Fluke digital meter

    If you are a DIY working on your personal engine , buy a DVA adapter and a brand name meter. If your going to work on customers buy a analog DVA in link below. Same meter Mercury sales/uses. FLUKE does not sale a meter with built in DVA adapter...
Top