Search results

  1. roscoe

    When opening throttle, inline 6 speeds up for 20 s and then lose power

    Primer bulb needs to be between filter and outboard. The bulbs contain check valves to prevent one engine from drawing fuel from the other. So you will need 2 primer bulbs, one for each motor.
  2. roscoe

    Tower of Power Cold Start Questions

    So ? all you did was eliminate the squeezy bulb.
  3. roscoe

    Seeking Opinions/Advice on the Boat I Just Bought.

    Great looking project boat. Many options on how you finish it. We have a Starcraft boat forum that is very active with aluminum boat restorations. Lots of info and ideas for you. https://forums.iboats.com/forum/starcraft-boats.131/ Polished metal is blinding in the sunshine. Painting...
  4. roscoe

    Tower of Power Cold Start Questions

    My 115 seems to have been modified by previous owner, a retired Mercury engineer. Not sure what he did specifically, but carbs are not original. He may have cobbled a pile of parts together to make the motor for all I know. And I don't have a cold start lever to raise, only throttle advance...
  5. roscoe

    Rigging outboard question

    Prep surfaces with acetone. Install mounting bolts half way. I use tape to hold bolts in position if they aren't long enough to put the nuts on. Then apply sealant to transom holes, bolt shafts, and around edge if transom bracket. Then slide bolts the rest of the way in and install washer and...
  6. roscoe

    Tower of Power Cold Start Questions

    My 90 and 115 start differently. Both require substantial throttle advance. 90 - need to hold key in until it starts. 115 - if I hold the key in for more than 5 seconds while cranking, there is a good chance it will flood. So I give it 5 seconds with key pushed in, then without. On occasion, I...
  7. roscoe

    Rigging outboard question

    3M 4200 Atwood makes a similar product with similar name. Sillycone has no place on a boat.
  8. roscoe

    89 blue fin spectrum 1900 ignition problems wont start

    Need to disconnect kill switch, not jump across it. Outboard kill switches ground out ignition when closed. Disconnect it at the engine.
  9. roscoe

    89 blue fin spectrum 1900 ignition problems wont start

    circuit breaker or fuse on the motor itself. deadman kill switch. Neutral safety switch. starter solenoid
  10. roscoe

    Suggestions for a Phone Mount?

    How about a waterproof case made for mounting on a motorcycle or bicycle ? They make them with RAM ball mounts too. https://riderlygear.com/product/waterproof-motorcycle-phone-mount/?gclid=EAIaIQobChMIk8mb0Ybd8gIVJiitBh3OGwzfEAYYBCABEgIVUvD_BwE...
  11. roscoe

    1956 StarCraft 16' boat? (ID help) please

    Have seen many starcrafts. I'm gonna go out on a limb here and say it is not a starcraft. It is and will be whatever you can make out of it, and whatever you can get it registered in your name as.
  12. roscoe

    New member, first boat

    sure looks like new.
  13. roscoe

    Major two stroke screw up Force 120

    Well that kind of flies in the face of the owners manual that tells you to use double oil 25:1 during the break in process.
  14. roscoe

    Major two stroke screw up Force 120

    You're really gonna have to explain how a plug not firing will cause a lean condition. Fuel and air will still be going thru the cylinder even if the plug doesn't fire.
  15. roscoe

    1989 Force 125 prop options??

    i suggest you post this question in the FORCE forum to get a better answer to your question. http://forums.iboats.com/forum/force-chrysler-outboards.29/
  16. roscoe

    Major two stroke screw up Force 120

    run it down 1/3 tank and correct it slowly Risk is that the air-cooled oil will not completely burn off due to the lower operating temp of a water cooled outboard. So you may foul a plug, or cause a little carbon build up, but should not be a problem for this limited amount. Maybe add a little...
  17. roscoe

    2016 Alumacraft transom rotted completely out.

    bummer. well, atlas it will be easier than a transom and stringers in a glass boat.
  18. roscoe

    2016 Alumacraft transom rotted completely out.

    Would really like to see a couple photos of this. thanks.
  19. roscoe

    Anti Cavitation Plate Height

    I think with a 5" setback from the jack plate, that you will need to raise the motor. Raise it an inch and then try it. Then try moving trim pin in one hole at a time.
  20. roscoe

    1985 MR180 Windshield

    There are a few options on these 2 pages. Check the dimensions. Apparently some models came with different size consoles and windshields. You can choose from clear, tinted, or green tinted. https://www.updplastics.com/star-craft-boat-windshields-1980s-early-1990s-models/...
Top