Search results

  1. Faztbullet

    Johnson 150 Rebuild/Remanufacture Guidance

    Going to disagree.... I have been using the caged for years and no problems(so has Merc) and no you need not use washers. All the Hi-Po motors use em and even Wiseco supplys them. Use em and go.
  2. Faztbullet

    2004 Mercury 150XL SWB

    Factory OEM
  3. Faztbullet

    Seal in shift shaft bushing - Classic 50.

    Dremel tool and cut one side
  4. Faztbullet

    Thermostat housing hole.

    Yes I have gave my verdict and it is not worth testing as its to damaged. it now has bent areas.
  5. Faztbullet

    Johnson 150 Rebuild/Remanufacture Guidance

    Same thing in different can....
  6. Faztbullet

    1995 Mercury 150 EFI no fuel

    Check the fuse holder for fuel pump...the connectors melt out
  7. Faztbullet

    Thermostat housing hole.

    The leading edges are burred...you can have the prop touched up/trued for around $40
  8. Faztbullet

    Thermostat housing hole.

    You definitely need to repair/replace the prop as it will cause too much loss of thrust. RPM will be high and speed low and both readings will be incorrect.
  9. Faztbullet

    How critical of an issue!

    Epoxy will not hold...either weld or replace. Use a TIG .
  10. Faztbullet

    97 Johnson 25hp goes into “limp mode”

    No limp mode...must be dropping a cylinder..check ignition when it drops out.
  11. Faztbullet

    Reed question

    It is called a reed clamp. it is not sold separate on Junkrude motors ..only as a assembly.
  12. Faztbullet

    How critical of an issue!

    Yes a complete will just bolt on...to swap your internals to a different housing will require the tools
  13. Faztbullet

    How critical of an issue!

    Housing also holds propshaft carrier in position via spanner nut. This damage can cause nut to jump threads and allow water or carrier with shaft /gear and prop to exit housing in a full reverse thrust mode. Fix it now or replace housing. Replacement will require special tools and set-up,
  14. Faztbullet

    A87076A4 idle speed control

    You dont need it.....it has caused many a cylinder failure
  15. Faztbullet

    88 Special Carbs

    Make sure you use new gaskets when clean/rebuild carbs
  16. Faztbullet

    Slow 9.9 Mercury

    Love this video..a perfect example of High HP and engine height and prop surfacing...just 12-13% slip at WOT. Will this work fro a 9.9...not quite but 1ich below bottom is a god all around set up.The deeper the motor the more drag and less speed/RPM. Fastbass Marine TV - Sportsmaster Lower...
  17. Faztbullet

    Outboard Overheating?

    Because its a water pump indicator..only shows water pump is working, not a test of cooling system.
  18. Faztbullet

    I have 1999 Mercury EFI 150 and the bottom end has clunk when accelerating not every time. Also the rpms have increased from 5200 to about 5800 .

    Check your prop hub if a 1 piece ...
  19. Faztbullet

    Steering when steering left it goes right can anyone help

    What year housing did you use? There is a difference in the worm gears
  20. Faztbullet

    1976 Johnson 115 Rebuild/Upgrade Help

    Sorry but boring will not make any noticeable HP increase. That motor is pre prop rated HP and is only about 90-95 HP at propeller. You dont have trim so best option is to true heads and install gaskets. Then check compression, if good then check spark and rebuild carbs and fuel lines. Head...
Top