Search results

  1. alldodge

    Impeller change / overheating / milky gear oil

    If the impeller is not pumping sufficient water then exhaust gases can back up and melt the tube The missing seal can causes issues, but to find out if the drive is sealed, pressurize the drive prior to filling with gear lube. Pressure should be no mor then 10 psi and do rotate the prop and...
  2. alldodge

    Thread Locker Choice

    No thread locker
  3. alldodge

    Thread Locker Choice

    Your in the Merc section so I'm assuming its a Merc drive. Which one (Alpha/Bravo) and at least what year?
  4. alldodge

    Mercruiser 3.0 MPI 2016

    Pressure should be 43 psi at 1800 rpm Being an EC motor, do you have the engine serial number and does it have digital control or mechanical?
  5. alldodge

    '97 MCM 3.0 LX

    Check the gray wire with coil disconnected from harness, and disconnect tachometer, then to determine gray wire is not grounded. Disconnect the shift interrupter If you get power to the coil when key is turned ON, and connections to other wires are good, then I would say it most likely is the...
  6. alldodge

    PWC Lifting Sling

    Bought 4 - 2in wide, 4ft long lifting slings from US Cargo The slot on the bracket is so tight I had to cut away the vinyl to get sling eye thru. Debated on to push eye through the slot and use a bolt of some sort to keep eye being pulled back thru, or loop the sling back thru the eye. The...
  7. alldodge

    Filter crossover

    Ya know, that said I can find the QS filter for under $10 Edit also Supersedes: 35-8226261 35-822626Q05 35-822626Q2 35-822626Q04 35-822626A2
  8. alldodge

    Filter crossover

    The Serria number crosses to Wix 51358 and 51358XP
  9. alldodge

    Welcome Back!

    Yep, worked again
  10. alldodge

    '97 MCM 3.0 LX

    Did this issue just start or was there anything which shuld some kind of signs prior? Being a 97LX and no serial number it should have EST distributor. Check the distributor
  11. alldodge

    Welcome Back!

    Hey, email notification works Ding, ding, ding we have another winner :cool:
  12. alldodge

    Welcome Back!

    Looks good
  13. alldodge

    No fuel - 2002 Mercruiser 5.0 MPI

    What is the voltage level of the battery? Check for 12V at the main power relay when key is turned ON. Should have full time power on the Red/Purple and Pink/Green. When key is ON should see power on pin 87 Red/Black
  14. alldodge

    PWC Lifting Sling

    It's strong but leaning toward quality 2 inch strap and sliders. This way I don't need to sew it together (have sail palm). Will look for ones with a load rating specified This would allow me to adjust and be good
  15. alldodge

    High Oil Pressure on Mercruiser

    Don't think its oil pressure Need to go thru the SC gauge and see what's causing the beep Here is what causes beeps
  16. alldodge

    PWC Lifting Sling

    Have a PWC lifting sling I bought several years ago. Its a Erickson (Made in China) rated at 1000 lbs and says right on it "use at your own risk". Did not notice the label when I bought it, but did understand the rating. Have lifted using it numerous times. Used it today, lift a bit and go back...
  17. alldodge

    Beware New old stock

    Dated August 2015, bought 2 years ago (2018) so it was 3 years old when purchased My Rinker Removed the belt driven fuel pump and raw water pump assembly at the end of last season. Rebuilt the fuel pump side because found it started to leak last week. I buy Merc brand new raw water pump kits...
  18. alldodge

    No voltage to fuel pump

    The relay which is energized by the purple wire is the Main Power Relay (MPR). Since it does energize then were good for that one. I am puzzled about wire colors. I see purple as 85, and Black 86 (ground). When energized power is transfered from Red/Purple 30 to Pink/White 87 Unless there...
  19. alldodge

    1988 mercruiser 350 thermostat right against block

    Howdy I'm fully understanding all your saying, but your thermostat should be the design one
  20. alldodge

    Replacement ignition switch

    Should wire the same
Top