Search results

  1. alldodge

    Suzuki df150 getting fat

    Good looking boat, but think I would insist on it coming with a prop :D :rolleyes:
  2. alldodge

    Chrysler 130

    Keep look for another motor or block to replace my 105. Frank told me I could use a 105 (original) 120 or Force 120 and change my cowling so long as it was before 1994. Found a boat and motor on CL but guy says compression is 132 across the board (skeptical) and its a mid 80's motor. I didn't...
  3. alldodge

    Pintle Hitch

    Over the years I have accumulated all kinds of hitch balls (pun intended). Have the straight 3-way, a couple 2 5/16, variations of 2 inch drops and picked up a pintle hitch some years back when needing a 10 ton Tag trailer. Was out today moving the Tag trailer and an empty cruiser trailer to...
  4. alldodge

    Fuel Pump/Pressure Problem Or Something Else? TIGE Mercruiser Magnum 454 EFI

    No, you test high pressure on the fuel rail at the shrader valve which is under the intake plenum. Removing the top lets you see if there is any crud building up. The high pressure pump can be lifted out to have a look
  5. alldodge

    Volvo AD41P RPM Issue

    Not saying your wrong, but in all fairness, the only place I've ever seen CAC has been with VP. Been on the Heavy Equipment Forum for as long as here and never seen it, all call them inner coolers. Most cases for low rpm in these motors is clogged exhaust, turbo or fuel pressure. Running...
  6. alldodge

    Fuel Pump/Pressure Problem Or Something Else? TIGE Mercruiser Magnum 454 EFI

    The motor says EFI but this is an MPI motor. The air intake plenum is only used on MPI. The EFI uses a Throttle Body Injection and sits on the intake where the carb would be, looks like this Here is the connections to the VST. In this case your mechanical fuel pump may be mounted on top...
  7. alldodge

    How to install dual battery

    Agree with add a battery, and what is the second bat going to be used for? Also install a battery switch or relay so it can be used to combine the bat's for starting if needed
  8. alldodge

    2005 Mercruiser 5.0 liter mpi with dual cooling Where is the Lifting eye ?

    Agree with this unless you have the thermostat housing ring hook installed, if its there use it. Loosen the top nut on the engine mount. Pick the front of the motor up until it is just off the front mounts. Adjust the lower nut until it makes full contact. Now lower weight off of motor...
  9. alldodge

    Bravo 3x power trim wiring harness diagram

    Here ya go
  10. alldodge

    Looking for a switch

    Find a plastic outdoor electrical box, couple extension cord connectors for the box, and a 120 wall switch and cover like the one below. Make your own, this is rain tight stuff. Or search for outdoor extension cord with switch and find things like this...
  11. alldodge

    Quicksilver 3000 Controls Replacement

    Yes, the limit switch is located on the drive. So if its connected to the trim switch, pressing the trim buttons will not allow the drive to go up all the way. If the limit switch is not there, or if it is bypassed the limit buttons will fully raise or fully lower the drive. It can be...
  12. alldodge

    Mercruiser 5.0 MPI no start/spark

    Some wiring diagrams
  13. alldodge

    Using boat during winter

    Look for drain kit 22-861505
  14. alldodge

    Tilt trim motor issue

    Are you looking for these items? If not, either post a pic or let us know which page the parts are on in the manual
  15. alldodge

    Loose engine mount found !

    Muc is correct, I pay more attention to the lock nut on top. The listing only calls it a nut but it is a nylock nut http://www.mercruiserparts.com/bam/subassembly/31770/1939/250
  16. alldodge

    8.1 Crusader winterizing ??

    What most do, is take a piece of aluminum, cut the shape out, then drill and tap a hole for the air fitting, then use a piece or rubber as a seal. It could be made from ply wood, but would need some kind of metal strap to go over it to screw down in place Some use things like sea flush for...
  17. alldodge

    Mercruiser MAG 350 with Alpha drive running hot when pushed hard

    I asked if you had a belt driven sea water pump on starboard side and you said Your pic shows an arrangement which does NOT have a belt driven sea water pump The belt driven one looks like this So if you have the pump you should not have an impeller in the drive
  18. alldodge

    1998 Merc 7.4 MPI won't start

    NO The jumper cables are being used to add additional grounds only from engine block to the battery, don't use them any place else. The slave terminals are the ones on top. One side is hot 12V and the other goes to the starter solenoid. When jumped across it should crank the motor without...
  19. alldodge

    What Mercruiser outdrive do I have

    Drives, and Bravos are new style swept back shown. The B2 turns a larger single prop then the B1
  20. alldodge

    Heat Pump Issue

    Electronic, and the AUX light is top left of the display
Top