Search results

  1. alldodge

    Heat Pump Issue

    Starting to get a house ready for rent and has not been lived in for about 3 years. Has a 2 1/2 heat pump by Rheem. When placed in heat, the electric coils turn on but the outside unit does not. The thermostat lights up AUX on the panel. If I go to cool, outside unit turns on and unit works...
  2. alldodge

    New to me bCrownline with problems high idle water in oil!!!!

    Where does the transom hose go to? You have the fuel pump section but not the water pump side?
  3. alldodge

    Help Re-Wiring Evinrude 88 SPL

    I found 87 also and think it should be 88M instead of 88W http://www.maxrules.com/models/OMC_models_files/1980_1999/75_150.html
  4. alldodge

    Can't Remove Flame Arrestor

    Pic's a plenty
  5. alldodge

    Help Re-Wiring Evinrude 88 SPL

    The motor was running fine 2 weeks ago, if it no longer runs what happened? This one looks like a trim sender This looks like a digital pigtail Main connector Where did these come from?
  6. alldodge

    Fitting a serpentine alternator on a Mercruiser SBC 350

    It might but your going to needs different brackets and probably a different ALT. Your motor year which is being used did not use a serpentine. In 1998 to 2001 used these arrangements. If you have an Alpha its top left, Bravo top right, with ALT bottom right pulley on both After 2001 the...
  7. alldodge

    Bennett Trim Repair And Auto Pro Install

    Installed the ATP unit next to the trim pump. This was the easiest place with the limited cord. The cord is about 2 feet and was glad my unit needed the adapter connecter which gave me another foot, would suggest at least 4 feet. If the motor was out, I would have placed it closer to the pump...
  8. alldodge

    Bennett Trim Repair And Auto Pro Install

    Back to the orange things: The orange pieces are part of the Port and Starboard trim connectors. Thought they looked weird but didn't dawn on me until after I was done and looking at left over parts. I then noticed the same orange pieces inside the connectors. Pulled the connector apart...
  9. alldodge

    best trailer jack..

    Have to know what you have to advise, or in other words
  10. alldodge

    Can't Remove Flame Arrestor

    Your not talking about this
  11. alldodge

    Bennett Trim Repair And Auto Pro Install

    Was running the port wires over to starboard side, then needed to put the connectors on the wire ends. Easy enough, just slide them in the connector until they lock. They come with tabs to mark the cables and looks like lock pieces (orange things) to keep the connectors from coming loose. They...
  12. alldodge

    Bennett Trim Repair And Auto Pro Install

    I removed some things and managed to get barely enough room to get on the starboard side. I can reach the stern, and just be able to turn enough to get to the pump. This is not fun No complements to the pump fill spot, its about a 3/8 hole which was a bugger to get trans fluid in. At least...
  13. alldodge

    Solenoid wiring diagram

    Being an OMC this should help
  14. alldodge

    Need Help w. My General Electrical Setup

    I'm saying in most cases it would be a house and start bat. Not saying it is but looking at your pic, it appears this would be the case. The breaker panel shows, breakers for Fridge, Macerator, Helm and others. {quote=]I see. So, basically by checking for continuity I might determine that...
  15. alldodge

    Upgrading Mercruiser Transom Assembly and Y Pipe

    You have a couple choices, this is what you have now You can either go for the next up grade which went to center risers and uses warm manifold setup. Or The new style (V6 but same for V8) which are cool manifolds. Basically the newer style allows excess water not needed for the motor...
  16. alldodge

    Need Help w. My General Electrical Setup

    I see you having this configuration now
  17. alldodge

    Need Help w. My General Electrical Setup

    I see you having this configuration now
  18. alldodge

    Need Help w. My General Electrical Setup

    First all grounds go to ground, including the house and two starter bats, otherwise you need an onboard charger just to charge the Inverter (house) bat. Lets call your bats as follows, 1) Start 2) House 3) Inverter, this way we can keep things straight. The normal configuration for batteries...
  19. alldodge

    ESA testing/wiring help please.

    Howdy I'm finding the 2.9 motor was installed in Rangers and Broncos from 86 to 92. The motor was never installed in a boat and this is the issue. ESA module needs to be connected to the distributer to cause the motor to miss. This is the wiring for the OMC V8 The wiring for the 2.9L V6 is...
  20. alldodge

    Bennett Trim Repair And Auto Pro Install

    Taped the control template in position. Think this would work better using something clear (in my case) or even wax paper. This way I could see in reference to the holes already their. If I do this again, might try something like that. Then cut the center piece out using a hack saw blade...
Top