Search results

  1. Lou C

    2025 should have a bumper crop of freeze busted blocks come spring

    “I shoulda spent the cash on closed cooling!”
  2. Lou C

    mercruiser 4.3 thermostat housing

    Also leaking intake gaskets were very common in the first few years of the Vortec engines & that will put water or antifreeze right into the cam valley and into the motor oil with deleterious consequences for engine wear. So if going that route make sure to use good quality gaskets and follow GM...
  3. Lou C

    mercruiser 4.3 thermostat housing

    If you do be aware that the torque specs for the intake manifold are much lower that they were for the the pre Vortec (like 10-15 lbs vs 30-35 lbs for the pre Vortec) and I think the procedure for torquing the head gaskets may be different as well….
  4. Lou C

    mercruiser 4.3 thermostat housing

    I thought of doing that with my pre Vortec, I had to replace the cylinder heads 7 years ago because of previous overheat damage. However I just wasn’t sure of all the details of the conversion (such as could I use the same pushrods & rocker arms) and so to keep it simple & avoid problems I just...
  5. Lou C

    Deep Cycle Battery not good for starting??

    So what about the so called dual purpose battery? I have used these myself for over 10 years with good results. Main concern is my is moored all season although covered. Still I want to make sure that the bilge pump had adequate pose in case water gets thru the cover which is kind of inevitable...
  6. Lou C

    Deep Cycle Battery not good for starting??

    I think if a deep cycle has enough CCA to crank the engine it should be fine. BTW, people forget sometimes that bad starters that draw too much current and old corroded internally battery cables kill batteries. Bad cables also won't allow the alternator to fully charge the battery. I had far...
  7. Lou C

    mercruiser 4.3 thermostat housing

    Yep the Vortec heads are designed for more efficient combustion and add about 20 hp. The FIAT reminds me of the air cooled VW Beetles we all drove back in the 70s as broke college students….
  8. Lou C

    Deep Cycle Battery not good for starting??

    I have had good luck with Deka lead acid dual purpose gp 27s. Not too expensive and hold a charge well.
  9. Lou C

    mercruiser 4.3 thermostat housing

    The balance shaft was added a few years before they started using the true Vortec cylinder heads. To add to the confusion GM changed to these plastic valve covers that say Vortec on them even though they weren’t using the Vortec cylinder heads yet…….that could be a 1994 or a 1995 model year...
  10. Lou C

    mercruiser 4.3 thermostat housing

    https://www.ebay.com/itm/405197631651?_skw=GM+4.3+marine+intake+manifold&itmmeta=01JGYVX1RDZPYHRH0E716XV4ZF&hash=item5e57a930a3:g:E9wAAOSwhJ5m0Ea3&itmprp=enc%3AAQAJAAAA4HoV3kP08IDx%2BKZ9MfhVJKlIv6QiWjOvmfdKbXgZ4Ndh1zZooF9wn1y1yMoYWEPfvzH8zBVtedY2RlRpS5YyvjDZDtlK0b67GIFc3X2Zk1UuT%2B7922acJP7%2BXYi...
  11. Lou C

    mercruiser 4.3 thermostat housing

    keep in mind there are 2 different intake manifold designs for the GM/Chevrolet 4.3 V6. There is the pre-Vortec (up to and including 1995) which has 12 bolts holding down the intake manifold and has the exhaust crossover in the intake manifold. Then there is the Vortec (1996 and up) which has...
  12. Lou C

    mercruiser 4.3 thermostat housing

    When I replaced the cylinder heads on my engine like 7 years ago I put the restrictors in and it's been totally fine. Our summer temps are 80-95*F so the restrictor allows the auto choke to work properly but it doesn't get so hot that I had vapor lock during hot restarts. At the beginning of our...
  13. Lou C

    mercruiser 4.3 thermostat housing

    The exhaust crossover was used on the pre Vortec engines because these engines were originally designed for carburetor fuel systems. As such there was a need for a way to bring heat into the intake manifold to prevent carburetor icing and to provide heat to operate the auto choke thermostatic...
  14. Lou C

    mercruiser 4.3 thermostat housing

    That’s an exhaust passage restrictor not a water passage so it’s fine to use as is. I did when I did mine 7 years ago….
  15. Lou C

    mercruiser 4.3 thermostat housing

    They look like the Fel Pros I install do when I did mine 7 years ago, also for the Pre Vortec not Vortec….
  16. Lou C

    mercruiser 4.3 thermostat housing

    Those restrictors are for the exhaust crossover in the intake to warm the base of the carb & auto choke spring. The restriction limits the flow to keep from overheating the carb base….
  17. Lou C

    I forgot the name of a recommended E10 gas tank cleaner.

    this new direct injection headache is what has caused me to hang on to my old '07 Jeep 5.7 Hemi, no EFI problems with this beast over 130,000 miles of use. I looked at the Bronco, the 2.3 is direct injected, the 2.7 has TWO (2) EFI systems, one to satisfy the clowns at the EPA, who need to be...
  18. Lou C

    I forgot the name of a recommended E10 gas tank cleaner.

    Thinking back when we had to switch from straight gas to e10, about in 2004/5, the only thing I noticed was a red jelly like deposit in my fuel filter, after that each year I have dumped out the fuel into a mason jar when I change the filter in the spring and it always looks like this: I seem to...
  19. Lou C

    Exhaust Boots Install

    If you're running in the salt like I do, then you want some grease on all the hose fittings on your thermostat housing, and circulating pump housing, or else even with hose picks you'll be cursing on a cold fall day when you start winterizing it. They WILL get rusted in place, learned this the...
  20. Lou C

    I forgot the name of a recommended E10 gas tank cleaner.

    Ironically E10 IS a fuel tank cleaner! That’s what seemed to cause the problems, the solvent action of the alcohol cleaned out deposits & varnish left from past use. I have not had problems with E10 in the boat but in small engines I installed a shut off valve and drain all carbs with float...
Top