Search results

  1. Lou C

    V-P 5.7 Gxi intake on 383 stroker?

    The right size carb with the correct jetting will give you what you want and will be easy to maintain with widely available Holley or Edelbrock parts. If not used to starting a carbed engine with a choke that’s just a little learning curve. Best part of this way is you will be free of Volvo’s 2...
  2. Lou C

    Rain needed

    We had a bit of a drought in the fall but it's been raining often now and we just got about an inch of snow which is unusual before Christmas here. The water level issue is what is great about salt water, it just never happens here. We have deep water everywhere every year. 8 foot tidal swings...
  3. Lou C

    Bearing carrier removal 1989 cobra 3 litre.

    All good to know. I don't know that I'd every try to take my salt water used Cobra apart, might be very difficult. I can split the drive but even removing the water pump adapter if it causes a leak would be challenging due to calcium deposits. I do have a spare freshwater unit that needs a...
  4. Lou C

    MerCruiser 5.0 Carb Engine Compression Test, Two Piston came back with Zero

    I think Muc's way is the most efficient to find out what needs doing. The fact that it's #s 5&6 suggests the manifold to elbow gasket, or leaky elbow and/or manifold, but it is worth doing more investigation to get a better diagnosis, and the leak down test will do that for sure.
  5. Lou C

    How Do I Remove a Stuck Gimbal Bearing?

    It would have to be quite high, like above the crankshaft pulley centerline. It actually makes more sense to me that the seal keeps water that gets into the bellows out of the bilge, so a failed bellows does not sink the boat....
  6. Lou C

    5.0 OSi-JF overheating at speed

    These can crack if the raw water intake hose doesn’t drain fully. The OMC Cobra has the same design & that plastic nipple can crack the same way. There is a drain plug on the side of the pivot housing on the Cobras to drain that area but the plugs sometimes get seized in place. Don’t know if the...
  7. Lou C

    80th Anniversary of the Battle of The Bulge

    We who have relatives who served & have long since nice departed this earth have the responsibility to educate today’s youth as to the sacrifices made and what those sacrifices yielded in terms of freedom. Don’t depend on others to do it, we must educate & inform….
  8. Lou C

    Trailer bleeding brakes. Part 2

    from what I see there the calipers look like they are mounted too low for them to bleed easily, is it possible to rotate the caliper mount to put the caliper at the top? If not you could disconnect the caliper slide bolts, slide it up to the top of the rotor, bleed it and then...
  9. Lou C

    Salt water leak

    I actually had that raw water intake hose pop off the metal fitting on the transom mount, that is what led to my overheat years back. Now every spring I get down in the bilge and check EVERY SINGLE HOSE CLAMP. This is why I won't have another one of these I/Os. Outboards don't make raw water...
  10. Lou C

    Salt water leak

    Yep that leak just isn't that bad your auto bilge pump should be more than good enough to keep up with that.
  11. Lou C

    Trailer bleeding brakes. Part 2

    Sometimes the problem you can have with bleeding disc brakes is where the calipers are mounted on the mount in terms of location, if they are on the 9:00 or 3:00 position they may not be high enough for air bubbles to rise to the top. On drum brakes this is not a problem because the wheel...
  12. Lou C

    Low Voltage to the Ignition Switch

    an old seat cushion to lie on when changing a starter makes it less painful. also when changing that impossible to reach steering actuator
  13. Lou C

    Low Voltage to the Ignition Switch

    As much as it pains your body you must get down in the bilge & up close & personal with the starter terminals battery cables & engine grounds. You’d be surprised at what you find. And the engine doesn’t have to be flooded, simply moisture in the air and temperature swings cause condensation...
  14. Lou C

    Need some help just bought 96 chris craft

    I think in that time frame they were owned by OMC just like Four Winns and a few other well-known companies. If you have the 5.8 Ford + Joint venture cone clutch drive, the good part is the drive/transom mount are really Volvo and still supported. The engine not as much, the EFI and electronic...
  15. Lou C

    Need some help just bought 96 chris craft

    Post up pix & see my post in your other thread
  16. Lou C

    Need some help just bought 96 chris craft

    Likely OMC or Volvo drive system which in those years was actually identical but painted different colors. Cone clutch drive just like a Volvo SX drive….
  17. Lou C

    Tinkering on the 4.3l this winter...

    I think for both Merc and OMC when you went from the 4.3 2bbl to the 4.3 4bbl you went from 175 hp to 205 hp so it's not a big jump but I guess comparable to what you get with the Vortec heads. My pre-Vortec came with the 4bbl Quadrajet and you can feel a definite surge in power when the...
  18. Lou C

    Low Voltage to the Ignition Switch

    I had a no crank no gauges condition one year that was caused by oxidation on the glass fuse base and tabs in the fuse box, for the ignition system. Fuse had continuity but there was too much oxidation for current to pass.
  19. Lou C

    My 84 4winns horizon 195 project.

    I don't want to start an oil debate, but look at how the Mercruiser syn blend 25/50 held up in my engine. I have used it for the '23 and '24 seasons so far, before that I used the regular Merc 25/40 conventional oil. And before that (like before 2015) I used Delo 400 40 wt. It also has more...
  20. Lou C

    My 84 4winns horizon 195 project.

    Sounds great. I am doing a few upgrades to my old boat, most will be done in the spring, I am going to take it back to the 'glass shop that painted it in Imron 13 years ago and have them replace the stripes and replace all the old FW Logos with reproduction ones plus the name we never put on it...
Top