Search results

  1. M

    Strange frequency and voltage on paguro vte 4000 diesel generator *with video*

    I dunno lots about these things but I do have a 2.5kw inverter that has an annoying qwirk , while it produces a sine wave at 50hz the top and bottom of the wave have a ripple . For the most part its not an issue but my digital clock only takes 11 mins to tick over an hour . Im thinkin that...
  2. M

    Reeds?

    Dropped a cylinder ?
  3. M

    87 50HP VRO Evinrude - Could this be my problem?

    Yeah but , Im thinkin of all the guys I have seen that just dont know how to drive a meter to its best advantage , and all the good (ish ) looking meters that turned out to be crap. Those cheap digital meters will do most home work shop stuff but you have to know how to work around their short...
  4. M

    Spinning reels

    I googled one up ....looks OK too, specially if it looks to have not done much work . Pull it to bits and make sure it has the correct lube where its sposed to be and it will probly be a keeper .:D
  5. M

    Random

    Yep , remember it well , but I thought " why the hell would anyone want that for a job " , its not even that your shoulder deep in beef but your face is inches from its arse and they seem to have no bladder control .....either that or they have a sense of humour ........nah #### that :LOL::LOL:
  6. M

    Random

    :Dugh! some actors just grate on me , Nielsen is one , Will Farrel and Jim Carry are a couple more that will have me lurching for the remote.
  7. M

    87 50HP VRO Evinrude - Could this be my problem?

    Yep , all the hundreds of thousands of peeps all over the world that use them are just wrong . :rolleyes: They are actually a very handy tool ........but you do have to know how to use them:)
  8. M

    Spinning reels

    Its mostly just the tip and I do fit ceramic tips to all my rods if it didnt come with one . Its an old hang up from my nylon days because the noise made is similar to the noise nylon made when it was rubbing against something it shouldnt be , and it reminds me of some of the crap reels I...
  9. M

    cooking

    We had Aunt Daisy's and the "Edmonds " cook books
  10. M

    Spinning reels

    I use a Penn Conflict 20 and an Abu Garcia Revos2 also in 20 size . While they are smaller reels they are solidly made and have a good drag and a reasonable bearing count . They will easily handle 6lb Rainbow Trout. I have found that a lighter weight set up is easier on the wrist . One...
  11. M

    cooking

    Some peeps will always try to re-invent the wheel.:)
  12. M

    cooking

    My Mum has a "Kenwood chef" ( with accessories :p) that is over 50 years old and still going strong . I did replace all the grease in the trans and replaced all the TRS wiring ..... probly 20 years ago.
  13. M

    cooking

    Or that aint the real issue .... post actual compression readings and serial # :ROFLMAO::ROFLMAO:
  14. M

    Car door panel

    use something with a straight edge .... ruler maybe , but yeah , Id do it on the door .
  15. M

    cooking

    :D I call mine the handbrake ......she doesnt like it :LOL:
  16. M

    cooking

    Himalayan Tahr burgers back legs minced up ( apparently the front didnt look so flash after being ventilated with a 7mm magnum ) This sort of hunting is well beyond my capabilities but I have a friend who hates his wife (:LOL::LOL: no he doesnt , but he spends a lot of time running round...
  17. M

    Car door panel

    I reckon spray on contact cement ( I use Ados F2 ) and do it in 2 stages . Id glue down the most of it 1st then after thats stuck and cured then roll the curved edge in . If you blow any loose stuff off 1st hopefully it will go back in place and be nice and flat , spose you could lay...
  18. M

    87 50HP VRO Evinrude - Could this be my problem?

    Those reeds look pretty damn good to me :)
  19. M

    Towing friends boat damage

    I would imagine "full responsibility " would fall on the operator. I guess too that there might be some question as to why the hitch came off in the 1st place . Can you get the repair done and hand him the bill leaving it up to him how he recovers the loss. Once he has accepted liability (...
  20. M

    Tohatsu

    + 1 for the fuel pump
Top