Search results

  1. D

    2003 Glastron VP 5.0 GL Overheat issue

    Keep in mind there is a seal and a bearing in the raw water pump. The seal should be replaced. It's pretty easy to replace. There is bearing also. Harder to replace than the seal but doable. In one of the pics the seal looks rusty. The rust is from the spring that part of the seal. I will...
  2. D

    SX-M repainting tips needed

    Go to Boatered.com. Look under Engines, etc and there is a pinned thread on repainting outdrives. It's the prep that's important. Forget self etching primer. It's an excellent writeup.
  3. D

    Malfunction indicator Light constant on

    I for one would rather just buy the Diacom than try and spend my time fooling with an OBDII and trying to get it to work on my VP boat engine. Then I will have more time to work on the VP boat engine.
  4. D

    Malfunction indicator Light constant on

    Most shade tree mechanics get a Diacom scanner and a laptop.
  5. D

    Does my GL-5 75W90 need to be official?

    With so little of the gear oil needs per year why not go with OEM,m
  6. D

    Sqeeking sound from belt after impeller inspection

    There is a shaft seal in the raw water pump. The rubber seal can get hard & brittle. If your raw water pump dripped a little I would replace the seal. This is the shaft seal, not the housing o-ring.
  7. D

    2006 volvo penta 5.7 rebuild help

    So what happened to the engine. It ingested water and rusted a few valves? Have you considered just pulling the heads?
  8. D

    Compression test

    The oil control rings scrape oil and prevent excessive oil burning. Above the oil control ring are the two compression rings. They are what control compression along with the cylinder walls. Dump a little oil into each cylinder and rerun the compression test. If it gets better your rings are...
  9. D

    Starting boat after 4 years - pre start steps

    Maybe send the carb out for a rebuild. They do more than just replace gaskets.
  10. D

    5.7 Switched 12v

    Did you figure something that stops the electric fuel pump if the engine stalls?
  11. D

    Compression test

    It's not clear if you had the heads machined (valve job?) or just new valve stem seals. Did the boat ever get on a plane quickly or boat new to you? Not getting on a plain can be many things from old gas to growth on bottom of the boat, to wrong prop.
  12. D

    VP SX drive low oil but no sign of leak

    There is really no place for the gear oil to leak out of that you cannot see. It's not like an engine and oil where the engine can burn oil. I would just keep adding oil until it comes out of the vent.
  13. D

    Volvo/OMC Raw Water Pump Repair/Replacement

    I could not install that on my engine. It's not red!!
  14. D

    2006 Volvo out drive thumping

    I do not think running with the drive up and a thump are connected. Running in shallow water can cause the outdrive to suck up muck or mud and if the props hit something it can damage the props and/or the outdrive. That can get expensive. Pulling the outdrive is not a huge deal but a duoprop...
  15. D

    Power Steering Cylinder Replacement

    I feel for you with that engine hatch. On my Chaparral I have full access to everything with the engine hatch up. I can sit next to the engine down in the engine area. And I often do.
  16. D

    2001 5.7 GSI flooding

    Are you talking EFI or TBI?
  17. D

    2004 5.7 GXI Overheat - Pump? Impeller?

    Also an IR thermometer can be handy. And when you get everything fixed take baseline temps of various components.
  18. D

    Volvo/OMC Raw Water Pump Repair/Replacement

    You can pull the old pump. Then pull the seal and look and see if the shaft is worn where the shaft seal seals the pump. If there is no grove then just replace the seal being careful not to tear it. Also check the bearing. The shaft should turn smoothly without any stiffness or bearing noise.
  19. D

    Tensioner Replacement

    I just ordered a new one as my current one has more of a "harsh bearing" noise than the idler when listened to using mechanic stethoscope.
  20. D

    2004 5.7 GXI Overheat - Pump? Impeller?

    Lower temp thermostat is for a RWC cooled engine running in salt water typically. The raw water pump has an O-ring. That needs to be on good shape. The raw water pump has a shaft seal and a bearing. The shaft seal is pretty easy to replace but the bearing needs a bearing puller, and an...
Top