Search results

  1. pvanv

    2000 m25c3 25hp 2 stroke flywheel

    No clue. Can you reattach the old magnet?
  2. pvanv

    Controls and prop for Nissan NS70A2

    Props are trial and error. Check WOT RPM to determine where you are now, and go from there. Most any binnacle control with TT switch will work. Single binnacle mount control box, with power tilt/trim switch & electric start. Control box only. For all TLDI models with power tilt & electric...
  3. pvanv

    90hp Nissian won't open up

    There is an exciter and 3 pulsers on the plate. I would test them. You want a harmonic balancer puller to get the flywheel off.
  4. pvanv

    8hp starts but runs only at high rpms

    Peter, My money is still on needing a Proper carb cleaning. I doubt you need rings.
  5. pvanv

    2004 Tohatsu 6 hp 4 stroke,Can't get lower unit back on...

    Take a break and try again. It's a matter of feel. The shaft is not aligning with the crank splines.
  6. pvanv

    2000 tahatsu 25hp 2 stroke worth

    Well, it's 20 years old, so not much. The flywheel has an MSRP of almost $500.
  7. pvanv

    8hp starts but runs only at high rpms

    You must disassemble the carb before soaking. After, blow out all passages. You may have a sticky float valve.
  8. pvanv

    90hp Nissian won't open up

    Several spots, especially in the low speed circuits.
  9. pvanv

    90hp Nissian won't open up

    Year of manufacture is irrelevant. You did not say, but you likely have an M90A. Clean the carbs with a proper overnight soak and try again.
  10. pvanv

    8hp starts but runs only at high rpms

    You can also swap to the 9.8 carb if yours won't come clean. Then you add power as well.
  11. pvanv

    Cutting out and stalling

    Temps should be about 150F. Did you reset TPS initial setting per the FSM? What are the fuel and air pressures?
  12. pvanv

    Tohatsu 9.8A3 EP no tilt lock

    Sounds likely.
  13. pvanv

    Tahatsu 30hp ptt solinoid replacement

    What is your actual model? 2 stk? 4 stk? Carbed or EFI? If 4-stk, the solenoids are on the front of the powerhead, and replacement is very straightforward. I would actually test the solenoids and verify wiring before replacing them willy nilly. Full info is in the Factory service manual.
  14. pvanv

    Cutting out and stalling

    Also check fuel and air pressures at the rail.
  15. pvanv

    Tohatsu 9.8A3 EP no tilt lock

    Check in the owners manual available at tohatsu.com. Sounds like you are only going to shallow water position.
  16. pvanv

    2007 9.9 Tohatsu/Mercury. No sparks.

    Can you post a pic of the motor so we can identify it? The Factory service manual is available for the Tohatsu 9.8, and has full detail.
  17. pvanv

    8hp starts but runs only at high rpms

    Yes. Likely the case.
  18. pvanv

    2006 Honda 9.9 Stalls in Gear in Idle

    Right. In my heated ultrasonic, I use regular carb dip (in 1 gal cans at the auto parts house), then after at least 6 hours, I blow out with generic carb spray. Works great.
  19. pvanv

    2007 9.9 Tohatsu/Mercury. No sparks.

    Merc 9.9 4-stroke may actually be a Tohatsu 9.8. If so, secondary to ground on the ign coil will be almost infinite. Also if a Tohatsu 9.8, you can test the CD box too.
  20. pvanv

    Tohatsu m25c3 2-stroke compression high on one cylinder

    If it's running OK, I would definitely do a decarbon spray through the carburetor and then re-check compression.
View older results
Top