Search results

  1. C

    Continued issues with 2001 evinrude

    If the engine does not fire but does cranks and you do not wish to venture to fast into HPP and injector diagnostics you can spray some carb cleaner in the air intake manifold. this is not usuall y recommended as the Carb cleaner will wash away internal oiling deposits from...
  2. C

    1953-54 25 horse evinrude

    I think this is it ... in the book btw Johnson service manual you need to service oldies..:) design intent for your safety .. I would not disable it but it is your motor. my Merc 7.5hp 1976 does the same thing... I can not pull the starter if not in neutral ! keeps one from flying...
  3. C

    Continued issues with 2001 evinrude

    back track... ficht have no carbs ... they have injectors. fed fuel from the high speed pump see manual ! see manul fuel pressure testing will tell you if the HPP is working ok to feeed injectors you need sparks easy to check * you need fuel in the cyl from the injectors you...
  4. C

    Trolling motor OMC Pt# 116063 replacement

    gas.. motors turn clockwise looking down on the FW.. to push forward most props turn clockwise hence ....the name right hand prop some props turn counterclock wise hence they turn as left hand props to off set prop torque double outboard or inboard set ups usually have one...
  5. C

    Leroy'S R.I.P. ???

    great move although I did recently copied the most good ones I needed (thanks to Matt) if you can share the file you have.... tons of folks could use it incl all the folks at the AOMCI again and possibliby others the file was restricted to AOCI members only folks under the main libary...
  6. C

    Trolling motor OMC Pt# 116063 replacement

    yep right hand... plastic props for electric trolling motor.!! https://www.crowleymarine.com/johnson/oem-parts/electric-trolling-motor/1999/hbfl2g/motor-adapter-group-12-volt-hbf2g-hbfl2g
  7. C

    Trolling motor OMC Pt# 116063 replacement

    but it is a right hand propeller which makes it even harder to find a substitute. right hand is common you must be meaning left hand like on some small 5hps ??
  8. C

    No sparking v4

    look for the mdl number on the engine....
  9. C

    Gas - Oil Mixture on old Evinrudes outboards

    if you dont shake the can the oil doesn't not mix and you run on near 0/1 for a while . Millions of those 4hp still run good so the problem wasn't the bearings....
  10. C

    1953 fast twin (15012)

    if you don'T have it you should download the bible...450 ages + on oldies https://watercraftmanuals.com/outboard/johnson/manuals/johnson-302231.htm
  11. C

    1953 fast twin (15012)

    see pict of typical old carb.... needles need round fiber washers to stop any air leaks into the low and high speed circuits . the washers allow firm needle rotation and keeps vibrations from loosening the needle . after tuning up the carb you can always give the nut a 1/4 or...
  12. C

    1953 fast twin (15012)

    "keeper " is to far in just loosen it a bit you did install the fiber washersaround the needle...? starter cable... just install regular starter cord. 7/32 ''
  13. C

    Need help finding part number for trim switch J50PLSNF

    the switch may be mechanically defective or the contacts pitted or.... any wire junction up to the parallel mating joint of the cowl switches may be oxydized loose whatever...
  14. C

    Need help finding part number for trim switch J50PLSNF

    I believe the switch needs replacing ? have you actually digged into it to check if power is actually transferred or not to the control wire all the way back to the relay ? . Switches do go bad but they usually carry very little current and it may be perfectly good. Trim switches are...
  15. C

    Gas - Oil Mixture on old Evinrudes outboards

    oil is cheap... motor are expensive.... go 24/1 on oldies 50/1 on non-oldies
  16. C

    2001 evinrude ficht

    good find! are you saying you reinserted the relay and the problem is gone ???? that relay first one under the two rows of fuses is the STOP/ING relay ( see pdpd drawing above) removing it may... have jiggled something inside and the fuse no longer blows.! If nothing...
  17. C

    2007 e-tec 250 lower mount corrosion

    doesn't matter if it doesn't fit
  18. C

    2007 e-tec 250 lower mount corrosion

    fyi if it fits... https://www.etecownersgroup.com/post/25-freshwater-g1-v6-midsections-13360804?trail=15
  19. C

    2001 evinrude ficht

    The plot thickens..... that R/B wire (in yellow) "fuseable link" into the PDP is also referred to as being a " fuse holder" on some versions ...of FICHT engines all fuses are fuseable by nature... so with the document I have I can't say if yours is that rubber fuse holder in the picture...
  20. C

    tilt and trim rebuild 2000 50hp Johnson

    Einstein said creativity was more important than intelligence... :) :) in other words need is the mother of invention
Top