Search results

  1. C

    Smokey Engine - Air/Fuel problem or Oil/Fuel problem?

    Check the fuel pump diaphram for damage. A damaged diaphram allows raw fuel into the crankcase. This can cause lots of smoke.
  2. C

    1982 Mercury 90 HP Choke Question

    Inline six right? There should be two plastic choke plates that close on the top two carbs.
  3. C

    1976 mercury 1150 115hp runs on muffs but not in lake

    Make sure your starter is spinning at 300RPM or so, to help it choke up.
  4. C

    1976 mercury 1150 115hp runs on muffs but not in lake

    No, as long the the primer bulb is hard, the carbs have fuel. Choke the crap out of her. Cold start lever high, hold choke button while cranking, until she fires. Hold choke for a bit and then feather it out, until she is warmed up. Make sure the voltage on the switchbox red and adjacent...
  5. C

    Prop Locking Question (Reverse Locking Cam?)

    I have a good one from a '77 IL6, here on the Jersey shore. You were in Ca, right?
  6. C

    New at this need help

    I am pretty sure this is the one you need for a standard MerControl. If you visit a dealer, he will likely have one, or can get one. https://www.crowleymarine.com/mercury/products/54211t-switch-assy The solenoid wire, terminal "S", needs to be wired thru the neutral safety switch. The...
  7. C

    Prop Locking Question (Reverse Locking Cam?)

    You could certainly get a bad gearcase on the cheap (maybe even free) and swap your stuff into it.
  8. C

    New at this need help

    The newer Merc compatible controls will work with your motor, with some modifications. The control cables for shift and throttle should work w/o any mods. You should be able to reuse your existing control cables with the new control. New wiring often comes with new controls and would usually...
  9. C

    Broken Skeg Tip...Repairable?

    Mercury used to make replacement skegs that could be welded on. You need to hire a good welder, who knows how to weld it w/o melting the seals, else you need to strip out the gears and seals. In your particular case, a skeg guard or some JB weld to smooth out the jagged stuff likely works.
  10. C

    BOAT PUNK

    There are a lot of symptoms that are well known to have specific causes. A gross example is a 70's inline Merc with water in the bottom cylinder. It is likely caused by bad crankshaft seals or a leaking exhaust component, either inner cover or baffle. It could in theory, be other things...
  11. C

    Prop Locking Question (Reverse Locking Cam?)

    I cannot answer your question, however, the older Mercs like your 850 had the gearcase with the rounded skeg (your bottom picture). The sharp skeg didn't come out until the 90's. I do not expect many here on the forum to know your answer, unfortunately. Rebuilding a gearcase is not a common...
  12. C

    BOAT PUNK

    Ken, There are a lot of inexperienced posters and lurkers. It is important to help them with clear, precise and correct advice. Giving them advice that is not known by you to correct and proper or recommending products that are contrary to OEM guidelines is not what they need. The forum's...
  13. C

    Merc 650 ignition system swap

    First of all Merc didn't make a 650 in 1990. Those old model numbers were out in about 1980 or so. You might check the places the distributorless stator and trigger bolt on areas. I doubt the distributor motor has those. If the pistons, rods and crank are the same, you could swap 'em over...
  14. C

    Gas line fitting

    Use a bag or cable tie, until you get one.
  15. C

    Gas line fitting

    Why do you not want to use the correct fitting? You want to cut part of the motor away instead? If you get an air leak into the fuel line, you can have running trouble. Can you reuse the old fitting?
  16. C

    Battery upgrade on Kayak

    10Ga wire is rated for 30amps. Is 360W enough for your trolling motor?
  17. C

    Renovating the deck floor top layer

    There are non slip products like fine sand that may be added to gel or paint. I would think the first choice is to save the diamond pattern, if you can. If the diamond pattern is beyond saving, you could use the sand additive, or go with carpet or vinyl flooring.
  18. C

    Water pressure gauge or water temperature gauge?

    Yamahas usually have a separate water jacket cover on the head. If you pull that, you can see if there is corrosion on the cylinder head itself. I am unsure what you meant when you said the pinholes in the water jacket were soldered. Usually, they leak water internally before they leak...
  19. C

    New at this need help

    It sounds like you have the new wiring colors. Red is battery power and goes to the "B" terminal. Black is ground and goes to one of the "M" terminals. Purple is ign power and goes to the "I" terminal. Black/yellow is usually the color of the ign killer wire and goes to the other "M"...
  20. C

    Merc won't shift regardless of position of the control handle

    That is the issue when installing the gearcase in forward. If the lower shift shaft is not turned all the way CCW, while in forward, the control often does not have enough travel to turn it to neutral. It is best to install the gearcase in neutral. The control also must be in neutral.
Top