Search results

  1. Scott06

    Electrolysis not a bad thing

    Would suspect the algee growth change is from something else as if stray electricity kept it at bay no one in marinas, which are known for stay current, would need bottom paint.
  2. Scott06

    Lumpy idle after carb rebuild | Holley 2300 | Volvo Penta 3.0 GS

    There may be a vacuum fitting plugged on manifold There is vacuum supplied through a small tube for the choke pull off Prob can put your gauge on there and just force the choke open Can also just tune it by ear or rpm when you go way lean and way rich it will stumble In Between these two...
  3. Scott06

    STUCK gimbal bearing.....

    Does it by chance have an older gimbal housing that A 2x4 across bellhousing will work as well
  4. Scott06

    Replaced Bellows now gears won't engage fully?

    is this in gear or neutral - thinking gimbal bearing, ujoints or propeller
  5. Scott06

    HELP I can't get my motor realigned

    That would be a good sanity check . Also seen folks us a 1" pipe or dowel which wont be tight in the coupler but allows you to insert it and look in with a flash light to see which way it needs to move. Be interested to see if the tool is wrong as that would be easiest solution. Would also...
  6. Scott06

    Help a little old lady with her little old mercruiser 120 wiring?

    I only have a gen 2 trim wiring diagram but it looks like there is a 20 fuse in the red between where it takes power off the solenoids and supplies it to the trim/trailer switches at helm and trim limit switch. Weather it was there originally or someone added a newer fuse holder to replace an...
  7. Scott06

    4.3 GXI SXA no water coming from seawater pump

    so if you have zero issues in three hours why did you insert clear hoses ?
  8. Scott06

    HELP I can't get my motor realigned

    there is a mercruiser procedure for centering the the gimbal bearing by inserting the tool and smacking it L, R, Up, down How far in does the tool go and what do grease marks look like ? I had to jockey my engine side to side when I did my repower Might be worth checking the tool dimensions...
  9. Scott06

    Overheating at idle

    the balls in thermostat housing are supposed to restrict flow of raw water to elbows, if they have debris could be passing too much water into exhaust starving the engine of cold water. Are you sucking air in at impeller if lower housing is corroded or water dam in there is damaged this can...
  10. Scott06

    proper shift bellows install.

    Manual 14 pg 4B-66 says to crimp shift bellows (zip tie is fine too) - it gives a spec for clamp to be 2.5" off the bellhousing.
  11. Scott06

    Tb IV intermittent spark ?$#???

    Yes
  12. Scott06

    Merc prop selector

    That's the hub I was thinking of Rubex...
  13. Scott06

    Merc prop selector

    Haven't busted either personally. Over time (many years) the pressed in rubber will slip, had several of those happen over the years. I think you are correct that the delrin will essentially act as a shear pin. You can get a spare hub sleeve for a few bucks. I keep a complete hub and thrust...
  14. Scott06

    Tb IV intermittent spark ?$#???

    https://www.marineengine.com/parts/mercruiser-sterndrive-parts/ they also have a page where you can drop your engine serial number in https://www.marineengine.com/parts/mercruiser-sterndrive-parts/ 90% sure there is only one TB distributor sensor which is here and has the rig terminal...
  15. Scott06

    Fuel tank leak

    Does he still have his eyebrows …
  16. Scott06

    Arcadia/Traverse Suitability?

    any of the vehicles except the 1k tow rated version will be fine. Your other thread on the Kia Telluride will work well too. What I found out when I bought my highlander is the higher tow rated versions of the Highlander (XLE) vs the lower rated ones - the difference wasn't in engine, trans...
  17. Scott06

    Holley 2300 2 BBL fuel filter

    the one I just took apart had a canister fuel filter by fuel pump and a screen in the inlet of carb
  18. Scott06

    Boat not take off when everyone sitting in the back

    Yes this is typical - when we ski or board in my sea ray 200 everyone wants to sit in the back row (4 across)- its gets on plane but much slower. The only thing that may help is what prop are you running and what is WOT RPM currently with that set up. If you are over propped it will help to go...
  19. Scott06

    XR 4 Hydrofoil

    As mentioned you will get conflicting recommendations. Like Jim I successfully used a DoelFin, as it helped my planning performance on an underpowered boat (3.0 merc IO). As others have mentioned it did break my AV plate... in the end I got better performance out of a lower pitch 4 blade prop...
  20. Scott06

    Merc prop selector

    Yeah everyone acts like on an alpha it is unacceptable to clunk going into gear but I think most outboards are dog clutch too? For your application I think they make a hub that is rubber vs delrin (hard plastic). Not sure if it is OEM Merc or aftermarket.
Top