Search results

  1. C

    1999 115hp evinrude ficht

    if the EMM says #4 is open it is not " communicating" with it electrically. or a worst case ... THE EMM is suffering mental failure (bad EMM) as far as the EMM is concerned it can not tell if an injector has a mecanical failure (except electrically of course. ) pull the J2...
  2. C

    pull cord not returning.

    ALWAYS WEAR SAFETY GLASSES THESE SERPENTS ARE NASTY ......
  3. C

    pull cord not returning.

    deleted
  4. C

    1999 Johnson 25hp 3 cyl 2 stroke oil lines

    Famous Lebaneese authour ...on giving Some possess little but willing to give completely Some give with joy and their reward is in giving Some give with pain and that is their baptism Some give with neither pain or joy and that is their virtue Giving without being sollicited is the...
  5. C

    1984 Johnson 35hp Throttle/Carb/Timing sync

    it runs well if you can return to the dock -)
  6. C

    1999 115hp evinrude ficht

    btw at just KEY ON the main buss will be at 12v not 40v.... 40 v is when the engine is running but the wiring testing is the same. At KEY ON the EMM does the initial sensing of sensors, injectors, ignition coils , etc... and calls the shot and declares faults on the side LED's and EV...
  7. C

    1999 115hp evinrude ficht

    typical inj resistance is 2-3 ohms refer to pages 174-176 in the 2002 + manual.
  8. C

    1999 115hp evinrude ficht

  9. C

    1999 115hp evinrude ficht

    typical injector to EMM J2 connector on 2002+ 115 HP FICHT PIN #1 GREEN white-black is 40V supply
  10. C

    1999 115hp evinrude ficht

    getting hot may be fuel flow cooling issue inside the inj or return hose ?? is the 2nd one getting hot also ??? the EMM likley means.... the injector circuit is open .. this does men that the injector's internal drive coil is OPEN . I doubt 2 inj.coils would be internally open...
  11. C

    98 evinrude DI 90hp

    without the conical filter #7 in the vst any degrading hose chunks or bits from a 25 old hose will be redirected into the HP pump and may reach the injectors. were injectors ever serviced ?? if you do take them out mark them and always reinstall in the same position !! the fuel pump...
  12. C

    Weird situation, looking for advice/how to repair

    you may be able to rebuild the missing chip by putting a back plate held by side clamps and doing some autobody filler (with glass fibers) to close it up... then sand and paint to finish the repairs and remove the back plate. nobody will know.
  13. C

    Oil Leaking from Bottom Unit Joint

    when they say DI engines are more fuel efficient it is becaue they burn all the fuel contained in the cyl. space provided before venting the exhaust out the back on old 2 strokes the exhaust ports are openned along with the inbound fuel ports allowing exhaust fumes to be pushed out by...
  14. C

    98 evinrude DI 90hp

    Done some reading on FICHT and the bigger engines 150 + were truly a pita it seems but....also see good comments on the 115 or less by satisfied customers. if no big mecanical issues come up or faulty EMM $$$$$ or rare/nla parts there may be hope...... but lots of reading to do ....
  15. C

    knock/grind/rattle at speed 90HP etec please help!

    suggest you submit same topic on the I3 ETEC owner's board for E-TEC expert support. see their SEARCH utility https://www.etecownersgroup.com/?forum=136483
  16. C

    98 evinrude DI 90hp

  17. C

    98 evinrude DI 90hp

    plugs must be grounded properly see comments #6 and #7 from another E-TEC case https://www.etecownersgroup.com/post/injector-and-spark-drop-test-8037482?highlight=testing%20sparks
  18. C

    98 evinrude DI 90hp

    AGAIN... BARBS crack easy !!! check for conical filter#7 which you can pull out with a large wood or metal screw twisted enough to just grab and pull. SINGLE filter can be replaced or cleaned with air/carb cleaner
  19. C

    98 evinrude DI 90hp

    ok so the lift pump is not the issue . if not adventurous and with so few shops wanting to work on FICHT ( no training , no info, no desire etc...) you may need to take time and read the manual provided and go one step at a time. STart with good electricals starting with battery...
  20. C

    93 e-tec with no spark

    E-TEC started post FICHT around 2003-4 btw fyi after about 20 minutes the edit feature goes out and you no longer can edit your post.
Top