Search results

  1. Scott06

    Sundowner 205 prop

    You don’t say if you can get to WOT without the engine hitting rev limiter ? I assume you run out of rpms before getting throttle wide open ? As outlined above u likely need more pitch either 17” or 19” would definitely recommend roughing things in pitch wise before u spend on stainless...
  2. Scott06

    Does E3 make marine plugs?

  3. Scott06

    888 running cold

    As mentioned would verify temp is accurate first Any blockage from a spent impeller would raise temps not lower them If it is low given your comment on cooling line mix up would verify that the cooling water flow is correct as to run too cool you would have to have water flow bypassing the...
  4. Scott06

    Does E3 make marine plugs?

    At some point GM wasnt using the Vortec name on enough engines so they called the 3.0 a Vortec 3000. suspect nothing is different vs the 3.0 … https://marinepowerusa.com/wp-content/uploads/2019/08/30lspecs.pdf
  5. Scott06

    Lost gearage?

    good to know it can be done some what easily.
  6. Scott06

    Alpha drive for a V8 whats the ratio?

    Ye cant have one with a 1.62 and the other drive a 1.47 ... If the engines are running 3000 rpm the prop shaft rpm diff between a 1.50 and 1.47 is 40 rpm. I doubt the throttle cables on a 1988 boat are synced that close. At some point merc tweaked their upper and lower gear designs that the...
  7. Scott06

    trouble getting reverse.

    rarely good news in old boats... Do you have closed cooling? That would be a nice option to have assuming it is working
  8. Scott06

    Ready to ride, summer projects?

    the adapter plate stays in between the exhaust manifold and elbow. I took it off and plugged it so i could use it on my GTO as well. I think the boat is pretty dialed in (a tad rich) so i dont know if put it on. it sat in a box all winter i was just gonna reinstall it on the gto now that the...
  9. Scott06

    Mercruiser 260 overheating please help

    First place to start is water pump impeller , if an alpha drive will be in the drive need to split haves. If a bravo drive it will be belt driven on the front of engine. also check exhaust manifolds and risers for plugging and thermostat while you are in there
  10. Scott06

    Correcting gear ratio with prop size

    picky? I think we got a bunch of bored guys waiting for spring , or maybe ran out of beer.... yes correct but we will correct for current in the slip calcs later on....
  11. Scott06

    Ready to ride, summer projects?

    pretty sure that is the oem manifold and made by GM. That is the only cast iron 4 bbl manifolds I have seen for the 4.3 Edlebrock manifold also seems to be single plane with a partial divider as well. Both like like each side of the carb is essentially feeding 3 cylinders I think until you...
  12. Scott06

    trouble getting reverse.

    If you are running a engine driven sea water pump with a through hull fitting for water pick up, then yes you want the hose to be cut in bellows area so impeller in drive is pushing water through the drive and out the cut hose to cool it. Engine driven pump will cool the engine separately.
  13. Scott06

    Swap an OMC 5.8 with OMC 5.7

    Yes I believe so. Even if the bolt holes need to be filled and re-drilled the transom cutout if the same. @Bondo can you confirm
  14. Scott06

    trouble getting reverse.

    When you run a belt driven raw water pump on an alpha , you are supposed to cut the water supply hose in the bellows area. The drive impeller still needs to be maintained to push water through the drive to cool it. Usually this is done if closed cooling is added.
  15. Scott06

    Swap an OMC 5.8 with OMC 5.7

    Cobra and Merc Alpha and Bravo use the same transom cutout. OMC was so far behind Merc in sales they wanted the cobra drive to be easy for boat manufacturers to use interchangeably with merc so they used the same hole. If you have the Chevy 5.7 complete it will be easier but hard to say if all...
  16. Scott06

    1992 Bayliner 4.3

    In addition to Teds comments - when you remove the plugs it should easily turn by starter or by hand. If it is locked up after removing plugs, pull the drive as it could be an issue with drive, gimbal bearing, or u joints as well. If you have to pull the drive an it is still locked up then...
  17. Scott06

    Correcting gear ratio with prop size

    Sure but better than the dash dreamometer for prop slip cals
  18. Scott06

    Building a '93 Caravelle 1750 Classic Bowrider

    A new block may be cheaper … seriously hope it turns out well
  19. Scott06

    Correcting gear ratio with prop size

    As others have mentioned what is your current WOT rpm ? What mph are you getting on GPS and what is the current prop? Is it a basic Aluminum black max or similar ? Is you engine in a good state of tune - no performance issues? I have a 21 ft sea ray with a 5.0, I have a 4 bbl carb vs your efi...
  20. Scott06

    How do I see if my jet ski is cooling itself

    My 2004 sea doo has a pee hole on side of hull below your left foot. Water comes out a bit at idle and hard and fast when at speed. This means cooling water is circulating. If your wear ring is worn the amount getting pushed out will be less. You may have a blockage somewhere. i belive this port...
Top