Search results

  1. C

    2000 E150FPXSSM LOOSES IGNITION ON START UP

    uppdate.... starting at section 4-19 book has a good technical write up on the ficht starter circuitry.. suggest your read closely...even mentions a starter delay relay....? anyhow... done all I can at my end of things :) maybe FICHT experts can chime in more readin to do here...
  2. C

    Evinrude family heirloom

    well... medicine has progressed to better :-) if one can afford it.
  3. C

    2000 E150FPXSSM LOOSES IGNITION ON START UP

    backtrack... been reading all this " My wife could feel the the ignition/stop relay fail as I left the key in on position. It would click on at first and click off a moment later with a no starter result." you mentioned your wife hears/feels the main ... "or a relay" click ON when...
  4. C

    2000 E150FPXSSM LOOSES IGNITION ON START UP

    manual has a good section 4 for electrical testing 4-23 covers the testing of the switch itself which you may want to investigate. I assume you are familiar with using a volt -ohm meter VOM if not there are lots of tutorials on utube. 4-50 and 4-51 has a clear diagram of the...
  5. C

    2000 E150FPXSSM LOOSES IGNITION ON START UP

    maybe a call to the ECM folks can give you more hints maybe they have heard of this ECM issue from other users meanwhile i'll ask a expert on the ETEC board for his opinion he is in Australia so answer will likely come back tomorrow :) btw....does you EV diag connect when the...
  6. C

    2000 E150FPXSSM LOOSES IGNITION ON START UP

    and patience brings joy.... that fuse blew for a reason I would focus on it ... hook up a test lamp or two at suspect points while dead and running state. see if anyone looses power as you fiddle with the key. clean that fuse socket contact pins with a folded emery or fine...
  7. C

    2000 E150FPXSSM LOOSES IGNITION ON START UP

    more info... https://forums.iboats.com/threads/1998-ficht-115-diode-number-or-spec-pn-0583898.664083/ https://www.cdielectronics.com/ficht/ a love story... read it all especially post#26 onward :-) and post #33 http://www.bbcboards.net/showthread.php?t=504541&page=2
  8. C

    2000 E150FPXSSM LOOSES IGNITION ON START UP

    check everything assoc. with power relay feed source, 10 amp fuse contacts and the fuse itself (try another one) pdd contacts to fuel pump etc... hold the key at START while DEAD .... have a buddy tap the PDP panel gently but smartly
  9. C

    2000 E150FPXSSM LOOSES IGNITION ON START UP

    see modern 200 hp etec layout
  10. C

    Evinrude 60Hp - wont stay running, help!

    In short, the motor starts right up, ?? does it just spin the engine or do you actually get ignition explosions while the starter turns the engine over ? . If so I think it is unlikley the kill wire (s) are grounded their role being to kill the ignition not the starter . As I...
  11. C

    1974 Evinrude 25hp wont run.

    before blowing $$$$ in suspected air leaks just wrap them up in cellophane tightly to prevent air leaks ... retry . you must be the unluckiest man in the oldies world at 130 posts ...:-)
  12. C

    1988 Johnson 15hp throttle cable retaining clip reinstall?

    deleted
  13. C

    1988 Johnson 15hp throttle cable retaining clip reinstall?

  14. C

    1990 evinrude 70hp boggs down at high speed

    maybe in here ? https://www.cdielectronics.com/wp-content/uploads/2013/03/CDI-Electronics-DVA-Charts.pdf?msclkid=da30c920c55e11ec819d0cfe0be40a4a
  15. C

    1974 Evinrude 25hp wont run.

    "The one thing I have found out is if you buy cheap you get cheap" agree 100% yet... I try to balance things between cheap and fleeced .
  16. C

    Tilt and Trim Seal Kit Help

    ask the folks here on IBOATS
  17. C

    1990 evinrude 70hp boggs down at high speed

    agree... yet carb is an easy first try.... before the big $$$ kick in
  18. C

    1990 evinrude 70hp boggs down at high speed

    how long ago was the carb job done...you may want to ask the mecanic why all his work does not allow anything above 2500 rpm . was the engine tested in any way after his work you paid for ?? tank venting ok ? fuel supply restricted somehow ? old style carb you could always try a blast of...
  19. C

    head & exhaust plate gasket replacement - 1970 4hp

    I dont apply sealants... orient the cyl head gasket top tab with the engine casing tab torque to specs .... retorque to specs after a good run is what I do . I do not use thread lock (blue) just some commom yellow teflon tape
  20. C

    1974 Evinrude 25hp wont run.

    i did, it does spit fuel in a good flow. looks like it is working OK better to look for another cause. hook up a small fuel supply directly above & into the carb inlet nipple and see if the engine runs with the new source of fuel. if it does not then the problem is...
Top