Search results

  1. C

    Fuel Nipple on Carb Broke (Johnson 60hp)

    any chance some (aluminum) JB weld goo would reattach the barb on the carb ? polish the carb with a SS brush and wash clean acetone or carb cleaner don't put to much to block the feeder channel into the carb ... after it sets add another layer of JB weld ... smooth it out...
  2. C

    1990 40 hp tiller won't run full speed

    and... is this a new sudden problem or.... a slow progressive problem over time ? How is the boat underside ...crusted up or clean ? Anything done to the engine before the problem started Is this a sleeper you are just waking up for the new season ??
  3. C

    1999 Evinrude Ficht E175FPLEEC dies at high speed

    If and I say if it is the problem my understanding is that the cold solder joints on the 12+ and grd pins can be gone over to resolder them . it probably involves removing the PDP and openning the back side to reach the culprit pins If you are handy with a voltmeter you can probably poke...
  4. C

    1999 Evinrude Ficht E175FPLEEC dies at high speed

    tapping (knocking) on the PDP apparently will... or could cause some reactions since it sends +12 to the T&T relays and other functions try a few knocks to see if things wake up or if the t&T goes dead with ..other functions faulting out atthe same time may as well recheck...
  5. C

    1999 Evinrude Ficht E175FPLEEC dies at high speed

    Google... evinrude pdp cold solder
  6. C

    9.5 1969-73 johnson air in fuel line

    I have installed several knoc-offs from China and they worked well but if you want the real things the folks at Iboats here can "fix" you up :-)
  7. C

    9.5 1969-73 johnson air in fuel line

    rebuilding the square pumps takes patience...and lots of it but after a few it is not bad . read a few times scribe/mark one side before taking it apart the to line things up on reassembly gets very confusing Rebuilding the OMC Fuel Pump (leeroysramblings.com)
  8. C

    1999 Evinrude Ficht E175FPLEEC dies at high speed

    ok I am no expert on much but... looking at the power dist. system ....that engine uses the famous Power dist Panel (PDP) and after reading lots of post those PDP ... they seem to have an issue with cold solder joints on main the B+ and GRD pins on the board ( 2 bottom ones)...
  9. C

    Hard Start 15 hp

    my snowblower starts at 0 F ... you outboard should start to I think you gas may be faulty if it does not vaporize at 45F
  10. C

    Hard Start 15 hp

    you did what exactly....close the choke plat shut ??
  11. C

    5.5hp Evinrude pressure conversion issues.

    what I have done in a similar situation is I simply added an extra inline filter which had barbs for 2 sizes it allowed me to connect the fuel source on one side .......then the thinner barb was used to feed the carb . extra filtering won't hurt anyway as to the pressure out...
  12. C

    Hard Start 15 hp

    choke linkage doing their job ??? do a visual has suggested
  13. C

    5/32 inch or 3/16 inch fuel line? 1986 60 hp Johnson

    difference is 1/16 or 1/32 each side of the ID try a clamp
  14. C

    1968 9.5 IDLE ADJUSTMENT knob

    try and locate all the impeller parts to see if you can get a picture of anything missing that could... have gone up and get stuck in the cooling cavities.
  15. C

    89 Johnson 60hp won't start

    thanks for your feedback....we all learn from it
  16. C

    1970 Johnson 6hp Problems

    thanks for your feedback.... lot of folks don't come back to tell what they found :-(
  17. C

    1968 9.5 IDLE ADJUSTMENT knob

    these motors (some models anyway) manage to smoke themselves to death by leaking exhaust fumes past the big seal in the lower housing and up to the carb . some have resorted to lobotomies in the cowls above the carb pita to take apart apparently and seal are manuf disc. if it...
  18. C

    1968 9.5 IDLE ADJUSTMENT knob

    well it should be a good runner with 75.... 65 is considered almost normal leroys is a great read which you have above utube has good carb videos and adj. the motor can.. live without the idle knob
  19. C

    Do I have a 'nice' engine?

    salty or fresh water life...? it looks... cared for ...outside if fresh water origins wash it, grease it, change the impeller and run a good decarb product (evinrude engine cleaner or Merc PoOwer tune) see how it runs ....on a fresh tank then decide if more work is needed for...
  20. C

    Need help with Johnson stinger J75TRLCSA PT/T

    see parts diagram.... any parts missing like... orings , seals, washers ...etc... where it leaks if and when fixed.. refill and run it up and down a few times ..then refill do this a few times to fill as much as you can and remove any air airspace Johnson Power Tilt And Trim Parts for 1980...
Top