Search results

  1. R

    Is my motor toast?

    In Canada----evinrudeparts.ca----might be able to help you.
  2. R

    1986 Evinrude 110 fuel issue?

    With the trim all the way down the bow would not shoot way up !!
  3. R

    Just bought new boat, trouble first time out. Please help.

    Too much oil is not a problem,----Does NOT foul the plugs in this day and age.
  4. R

    Replacing old 2 stroke with newer 4 stroke advice?

    Lots of electronic parts on newer 4 strokes and 2 strokes are listed as NLA.----So if you can't get that ECU during the season ???
  5. R

    Just bought new boat, trouble first time out. Please help.

    You need to be sure that the oil injection is in service or bypassed by a previous owner.-----Need to mix at 50:1 until you verify that system is indeed working properly.----Water going out the pee hole on some motors indicates that water pump is working.----But it does not mean that motor is...
  6. R

    1976 mercury 1150 115hp runs on muffs but not in lake

    Have you put a new water pump impeller in every 4 / 5 years or so.
  7. R

    Repowering from 1996 112 evinrude to 1995 115hp evinrude help

    The 115 does look like a 60 degree looper.
  8. R

    69 Johnson 60hp hydroelectric drive starts in reverse

    A 1969 would be a 55 HP model.-----Switch the shift wires and test again.----Model # is ??
  9. R

    Repowering from 1996 112 evinrude to 1995 115hp evinrude help

    There are many opinions on oil injection.----Up to you to verify that it is working .----Test warning system.----Test oil consumption.------Only you can decide what to do.----Have one of those motors apart for rebuild.----Owner neglected to commission oil injection and motor was destroyed with 4...
  10. R

    Johnson 48 spl fuse location

    Yes there is a fuse in the wiring harness.----Look for it near the solenoid.----A 20 amp about 5/8" long.
  11. R

    Is my motor toast?

    Looks like something loose inside the motor and popped a hole in the crankcase.----Your location in Canada ?
  12. R

    Verify model/serial number / Evinrude 70

    Correct it is a 76 model.------There really is no difference between a 76 model and an 81 model.-----Easy motors to work on.-----First thing is to post actual compression test values here.
  13. R

    Changing V4 crossflow from pre-mix air cleaner fuel pump mount to pulse pump

    The simple pump mounts directly on the intake manifold.---Mounts over the pulse port.----One hose for fuel in and a hose for fuel out.-----Remove pulse limiter and plug that port.----Re-arrange hoses as needed.
  14. R

    1986 Evinrude 110 fuel issue?

    Boat should be running about 50 MPH.-----Sounds like it is running on 3 of 4 cylinders.
  15. R

    1970 evinrude 115 - cdi pulse pack shortens out starter?

    Take starter apart for inspection.-----Do ohm checks.
  16. R

    Repowering from 1996 112 evinrude to 1995 115hp evinrude help

    Remove one motor and install the other.-----No need to change controls.----Install new water pump impeller.----Change gear oil.-----Commision the oil injection system ??----Test the oil injection system.----Perform compression test and record numbers for future reference.
  17. R

    1986 Evinrude 110 fuel issue?

    Post the actual values after doing a compression test.---Post them here.
  18. R

    Low RPM on a new outboard...All suggestions welcome

    Was the correct propeller installed?------
  19. R

    1976 mercury 1150 115hp runs on muffs but not in lake

    Open low speed fuel mixture screws 1/8th turn at a time and test run.
  20. R

    Fiberglass resin question

    I use West System epoxy.---More beer tokens I know.------I can no longer tolerate the smell of the polyester stuff.
Top