Search results

  1. C

    1965 6HP Gearcase Not Sealing

    can you try to JB weld broken area ... drill & retap as for gearcase pitting you could probably resurface it with some JB weld KwikWeld Professional Size | J-B Weld after a good sanding job.... clean all greases and dust mix up some JB and smooth it over the pitted areas let...
  2. C

    1989 70 hp evinrude won't crank

    Great news :-) glad you got her fixed up and gave us the feedback . I had a similar issue on a MERC 50 years ago. .found a broken wire in the side fat connector, the result of years of bending .
  3. C

    1973 evinrude 135 starflite

    look at it this way $1000 for a potential boat anchor is pricy.. it will need some work (impeller carbs, ignition check,gear case etc,,, Being a possible low hour engine is great but 32 years is a lot of time for rusting due to humidity , bugs etc... try for $1000.. an able bodied...
  4. C

    1989 70 hp evinrude won't crank

    progress..I get 12 volts on that wire. I get 12 volt into solenoid an Checking other points (like primer solenoid ) today ok if you have 12 v one of the control posts of the selenoid then the other small post would need to be grounded to get the internal coil energized on some circuits...
  5. C

    1989 70 hp evinrude won't crank

    great .. getting more difficult to get diagrams with Adobe flash player now R.I.P. thanks for info. o.p. mentionned NO spark when jumpering the selenoid .. odd that it is not sparking and selenoid is not working. testing and tracing seems in order. "starter is good as...
  6. C

    1971 evinrude 9.5

    got a freebie myself MQ13 if correct all white missing a carb link and parts. when I flipped it upside down all the missing parts came out. :) with some sand ... and crud
  7. C

    1989 70 hp evinrude won't crank

    the fact that you have 2 symptoms (no sparks... no start) would indicate it would be a very bad lucky situation to have a bad selenoid. selenoids are simple devices with a single internal coil to magnetically close the starter circuit . the control wire should show 12v while in START...
  8. C

    1989 70 hp evinrude won't crank

    did you mean D ??? sinc A would be solid bat +12 and B the selenoid output to the starter when coil voltage is applied on C &....D
  9. C

    1971 evinrude 9.5

    dont want to hold up this thread...but on this subject of condensers 7.5V or 120AC (rectified I presume) would generate a test voltage much lower than 270DC in W.Mohat's test box. His test box would seem more sophisticated to test a shorted or "leaky" condensers.
  10. C

    1971 evinrude 9.5

    thanks for info on condensers i'll include a warm up on the next one's I test in the future.. just out of curiosity do you know what voltage level was used on the Merc -O-Tronic tester . The AOMCI w.mohat tester i built checks out at 270 DC oddly my problem is at start up so my...
  11. C

    1971 evinrude 9.5

    I envy a one pull cold start 9.5 :-) my beauty 9622a Evinrude is a bear to start and I have pretty well all I can do and I mean all ! After the bear wakes up with a shot of carb cleaner it will run smoothly all day long trolling. Now that I built me a capacitor test box I will go over...
  12. C

    1971 evinrude 9.5

    2x Ignition Coils For 580416 584477 Outboard OMC Johnson Evinrude 1.5-40HP | eBay slow mail but cheap
  13. C

    1971 evinrude 9.5

    doing a carb job is not complicated see good utubes ...it is good insurance dont forget an impeller and new gear oil (check for water intrusion) (596) 9.5 Hp Johnson Evinrude Outboard Carburetor Rebuild - 1of2 - YouTube when you reinstall the carb carfull with the cam follower/carb set up...
  14. C

    Need Kill switch Repair vs. Replacement 1985 6hp E6RCOB.

    these are nice and water proof with easy mounting (Pack of 2) 19mm Momentary Push Button Switch Waterproof Stainless Steel Metal Flat Top 12V 24V 36 DC 110V 250V AC 5A 1NO SPST Screw Terminal APIELE: Amazon.ca: Industrial & Scientific just fill the end of the throttle with goop rubber for...
  15. C

    1999 Evinrude 115 Ficht - cold run issue?

    reminds me of my 75 etec crashing to SAFE MODE with NO OIL code 38s on cold start ups (fixed with new oil pump and S/W update) most hard shut downs on todays EMM are related to - high engine temp (unlikely) - high emm temp (unlikely) - to many NO OIL alerts ( newer xd100 cold...
  16. C

    1969 6HP Impeller replacement

    fyi I just ordered 3 thermostats from EBAY for 10$ CND ..about $7 U$ a piece with free shipping. from seller VKI_GO my lower price bid was accepted :-) I offered 10$ CDN for 3 instead of $13.00 each don't forget the rim gaskets !!
  17. C

    Trying to start a 1967 33hp Evinrude no Generator

    Boatinfo - 1922-1964 Johnson Service Manual this book does not cover your model but being a good old magneto engine you will find tons of valueable info on carbs, magnetos etc... utube has lots of info on fixing /tuning magneto engines like yours testing coils points etc...
  18. C

    Gear oil leak 1985 9.9 Evinrude

    you are running in cold temps with sharp variations while running the engine then shutting it off possibly generating some condensation in the lower exhaust routing..and drain. could be just sludge- crud oil and gas exhaust mixing and draining down and out. it also seems to come out...
  19. C

    Cowl replacement or repair.

    I have use "BONDIC" to repair broken bolt tabs on the ETEC lower plastic housing then cover up the "welds" with pieces of fiverglass cloth inbedded with permatex PLASTIC WELD Bondic is an instant weld UV glue for plastics (works just like dental repair putties your dentist uses and...
  20. C

    Cowl replacement or repair.

    how bad is it ?? pictures ??
Top