Search results

  1. C

    Whats good???

    I don't think you will have any psi issues with 120+
  2. C

    Whats good???

    probably 100+ but... what are you seeing ?
  3. C

    Need quick help: The Tilt Support Bar on my Etec wont move after tilting engine up, due out tomorrow!

    how about some spray lubricants to release rusted stuff. Teflon sprays are great but plain old WD40 should do and when your done it is like the other rusting....wire brush it, prime it paint it wax it
  4. C

    What is this rusting at the end of the steering bar?

    if it got that way....it is called neglect by the p.o. a wire brush, scrapper blade, primer and ETEC blue paint and the problem is gone... for a while then repeat :-) at the annual inspection with lots of TLC .. I car wax mine twice a year to ! as for the cracks ...you know how!
  5. C

    1958 Fastwin 18 lower unit won‘t drop

    Have you tried soaking the top splines with some release agent by flipping the engine upside down and sending the lubricant down to the upside down powerhead via the drive shaft and wait patiently a few days.... then retry if it does not work... flip it over again and resoak the...
  6. C

    1971 evinrude 9.5

    you must read Leroy's article on your motor... .all this is clearly explained both the lower speed idle limiter and the high speed linkageto prevent high rpms at start up are mentioned Johnson (leeroysramblings.com) btw careful never force the throttle otherwise you can strip a push rod in...
  7. C

    6hp fisherman idle issue!!

    do the easy stuff first Racerone's post#4 is critical ...to progress you need to answer all questions have you tried pumping the fuel bulb in case the engine is starving Rebuilding these carbs may only entail a good cleaning of all passages and blow dry them. did you check the...
  8. C

    1971 evinrude 9.5

    timer... tiller handle ? to reach FAST you must be in gear otherwise the interlock blocks the weird linkage in front of the carb to go lower than shift ....you must rotate the round idle speed adjustment
  9. C

    92 Johnson 60HP continuous alarm

    disconnect the overheat sender wire at the buzzer maybe it is grounded along the way not clear which end you disconnected
  10. C

    115083d no spark

    hopefully he did 8 years ago ....
  11. C

    Just bought a 93 48spl

    dual lines ended around 1960 's if you got a dual line tank ???? keep it if it his not leaking... parts are rare and in demand the motor side hose connector may be worth 50-75$ US you can sell it to a guy who needs one.
  12. C

    6hp fisherman idle issue!!

    what did you do to "clean" the carb ? did you inspect and clear the top drip chamber and the very small orifice feeding the top half of the carb via the side fuel channel ? see carb issues on older carbs yours has no bowl but basic issues remain
  13. C

    Evinrude Big Twin 35 Restoration

    folks at the aomci ask a member can help out also on reviving your oldy Ask A Member | Antique Outboard Motor Club,Inc (aomci.org) you do not need to be a member to ask questions they can guide you to a parts list for your 1958 gem OMC outboard related articles (leeroysramblings.com)...
  14. C

    1999 Johnson 70hp not peeing

    if you pull the thermostat do you get water on top on the engine ? have you tried running the pump on its own to see if it pumps properly ? water tube grommets not crushed ? missing any parts on the old impeller ? tried a piece of heavy fishing line up the pee hole ?
  15. C

    Evinrude 15 1992 Tiller arm low speed

    great.... having no specific parts diagram for that given mdl #...... ...I am out
  16. C

    Evinrude 15 1992 Tiller arm low speed

    looks like a Belgium made model... see an old post from 2008 ... b-----belgium e-----evinrude 15----15 hp ba----ac lightning -rope start en----1992 m-----model run or suffix dec 04 2008 Model Be15baenm Serial No 08916066 According to this it is a year 1992. When I look at the parts...
  17. C

    Evinrude 15 1992 Tiller arm low speed

    on the parts diagram the knob connects to a small cable which rotates a gear at the bottom of a vertical shaft.. presumably if you find the gear and shaft in your model one would think it should do the job of adjusting the throttle... please post your engine model on the plate
  18. C

    Evinrude 15 1992 Tiller arm low speed

    the end part in the diagram should rotate it seems.... tried some wd40 ? on all the parts Steering Handle & Throttle Control Parts for 1992 Evinrude 15 hp it is hooked up to a THROTTLE CABLE ASSY. which rotates a cam called SHAFT, VERTICAL CONTROL
  19. C

    1971 evinrude 9.5

    CAUTION... always wear eye protection to protect eyes and any tinted eyeglasses . carb cleaner can dissolve any protective coatings on eyeglasses yes.. just unscrew the lower bolt then use the plastic straw against the HS jet inside and the carb clearner solution will blow out the...
  20. C

    1971 evinrude 9.5

    high speed jet is fixed behind the lower bolt (keep it clean !! the LS needle unscrews.. carefull not to loose parts for points the highest point of the cam can be used and set points at .020 or sense when the pistons reach TDC with a screwdriver in the sparkplug holes. BUt.... you...
Top