Search results

  1. R

    1996 35hp 3 cylinder Johnson outboard

    If in Canada-----evinrudeparts.ca------Might help you.
  2. R

    1983 Johnson 115 hp not coming up to full power

    There are different opinions out there.------A rebuilt 1983 V-4 is a very good motor.-----You have to know how to start them.-----Uses more fuel than a new 4 stroke.-----Does not require $100/hr shop support.
  3. R

    Poor acceleration

    Pinch off the 2 little lines.----Or carefully remove those 2 little lines when motor is running.------No fuel should come out of the 2 small nipples.
  4. R

    1983 Johnson 115 hp not coming up to full power

    No surprise to me that shops are not willing to take this job on.
  5. R

    Need Help -Johnson 70HP 1975 Outboard Shakes

    Stated clearly---" see if spark jumps a gap of 3/8" or more "-----The test for spark gap has nothing to do with the sparkplugs you are using.-----Nothing to do with a cheap blinky thing either.------It is a maximum output test of the system !!----System is capable of jumping a gap of 1/2" if in...
  6. R

    Is my mercury oil injected?

    Many of us can hear that.-----But many folks say---- " Hurray, it runs and therefor there is nothing wrong " !!----That is my opinion only.
  7. R

    Poor acceleration

    The primer valve is an ultra simple device and easy to test its's function.----Pinch off the bigger hose to stop fuel going to it once motor is running.
  8. R

    Restoration project - 1965 AlumaCraft Maracaibo

    It is an important part.-----Should be easy to find as it was used for many , many ( 50 ) years.----Or depending on your ingenuity make one using a piece of a brass bolt .----Drill and tap and you are done.----Easy to make parts for older motor.-----Much easier than new motors !!
  9. R

    Yamaha 50 HP Idles to 3000

    See if control box pulls the throttle arm to the idle stop ( with a bit of preload ) each time.
  10. R

    Need Help -Johnson 70HP 1975 Outboard Shakes

    Do the following in order.-----Make sure throttle plates are closed at idle.-------Post the compression numbers first.-----Then see if spark jumps a gap of 3/8" or more on each lead.-----Then start motor with timing light hooked up to #1 cylinder.----Observe the flashing light.----Should flash...
  11. R

    Is my mercury oil injected?

    Many think that this motor has suffered.----But for the owner----" Hope is eternal "----and we wish him good luck with it.
  12. R

    Timimg on mercury

    You want to test / put ignition through it paces.---See if it develops designed output.---So does spark jump a gap of 3/8" or more on each lead.----You can do yourself a favour by learning to do this test !!
  13. R

    Ebbtide 2003 Hard shifting at the control box, cables are good ?

    What motor / drive do you have ?----Many drives need the propeller turning or motor running for smooth shifting.---Less damage to gear box that way.
  14. R

    Is my mercury oil injected?

    Nope.----The vanes take a set over time.----Have you tested the overheat horn in the control box if if it has one.----With no tested overheat horn you are taking chances.
  15. R

    Timimg on mercury

    Crankcase must be sealed with--- loctite 518---or equivalent.----No RTV to be used.----The question was-----Does spark jump a gap of 3/8" on all leads?----The question is not what kind of plugs are in the motor.----V-6 motors run remarkably well on 5 of 6 cylinders.
  16. R

    Johnson 150 v6 leaking gas at idle

    So is it a 1977 model or a 2005 model ?
  17. R

    Timimg on mercury

    What kind of sealer did you use when closing up the block ?---Does spark jump a gap of 3/8" on all leads ?----Wires from switch boxes hooked up to correct coils ?
  18. R

    Ebbtide 2003 Hard shifting at the control box, cables are good ?

    Cables can be put in either position in the box.----At the motor end the shift cable moves first.-----So hook it up / adjust shift linkage first.-----Motor must be running or propeller must be turned when operating the control box.
  19. R

    Is my mercury oil injected?

    Those inline 6 motors need a new impeller about every 2 or 3 years.----The noise is likely from mechanical issues caused from running on straight gas.-----Loose / scored piston comes to mind.
  20. R

    Will evinrude work on johnson

    For a novice it is always best to ask before you spend your beer tokens
Top