Search results

  1. R

    JW-10 will start, then die.

    Fuel filter in tank plugged ?
  2. R

    JW-10 will start, then die.

    You did install a new water pump impeller I hope.
  3. R

    1970 4 hp Evinrude stops suddenly

    Thirty five years ago I tried a sierra impeller on a little 2 HP Johnson.-----Took it out and tossed it in the garbage.
  4. R

    1976 Johnson 70hp will only run low rpm after warming up.

    The primer bulb is a simple manual pump to fill the carburetors for start up.------It saves the starter motor from doing that.-----Or on a manual start motor it saves your shoulders.-----And the bulb does nothing when motor is running.-----And the bulb does not stay hard when motor is running !!
  5. R

    Are muffs available for 1959 5.5HP Golden Jubilee?

    Find that plate on the side of the lower unit.-----Find the main water intake screen behind the prop.----Make and adapter for that plate for muffs or a garden hose fitting.-----Block main intake with tape.-----Test run.-----Don't forget to remove tape.
  6. R

    Sticking solinoid?

    I give up.----Wires and 12 volts are simple to me , but difficult to explain I think.
  7. R

    1970 4 hp Evinrude stops suddenly

    None of that era 4 hp motors have a thermostat !
  8. R

    Sticking solinoid?

    There should be a small black wire from small solenoid terminal to ground.--I can not see your motor.-----But that is the way it is wired on motors that I have !---
  9. R

    Short to Long Shaft swap on a 1995 20HP

    Agreed.----Good luck.
  10. R

    03 mercury 50hp 2stroke loss thrust

    The clicking is normal.----Nothing wrong there.---Check for spark on all leads.-----Do a compression test for reference.----Install another prop and test run.
  11. R

    Sticking solinoid?

    Replace the wee ground wire on the solenoid ?
  12. R

    20hp Johnson 1983 - Push Button Start Wiring

    From the solenoid battery + side you feed 12 volts to your push button switch.------From the push button switch you go to one small post on the solenoid. ---From the other post you go to one spade on the neutral ( white plastic ) safety switch.----Note the safety switch only needs ONE WIRE !!
  13. R

    JW-10 will start, then die.

    Look through the inspection hole in flywheel.-----Inspect coils , clean and set breaker point through that hole.-----In my opinion hard starting is usually due to weak spark.-----So does spark jump a gap of 1/4" on a test device.----Do not trust inline testers with a glowing light !
  14. R

    1986 Johnson 150 J150TXCDC Gearcase Seal Replacement

    If it holds those pressures it is all good.---Fill with the best BRP specified oil for it and go fishing.
  15. R

    Sticking solinoid?

    Agreed it could be the wrong solenoid.----Simply because the parts counter clerk and the buyer do not know that there is a difference.------And the model # of the motor is still top secret.
  16. R

    Gear case hole?

    Is there any water getting in your gearcase ?-----And some oil leaking on that outboard might be normal.-----It would be the oil that is mixed with the gas !
  17. R

    Short to Long Shaft swap on a 1995 20HP

    One issue is that sometimes the castings are the same.-----Then on some model they use bigger bolts / locating dowel / bigger threaded holes.--- than previous model.---This part would then have a different part # but can be used.----You could easily modify these parts.-------A good shop ( if...
  18. R

    1974 Evinrude 25hp wont run.

    Is the magneto plate bushing loose in the plate.-----Believe it or not if bushing is not lubricated it will wear from vibration during every minute that the motor runs.
  19. R

    Sticking solinoid?

    I can not see what you are doing.----Perhaps clamping the solenoid so tight that it is jamming it.-----I was not there !----Model # is ??
  20. R

    Sticking solinoid?

    So what motor is this ?---
Top