Search results

  1. R

    ‘63 Evinrude 3302s 3hp questions

    Water must be 8" above the impeller in a test bucket.
  2. R

    Evinrude 115Hp V4 Project Rebuild / Repowering a Fourwinns Fling Turbo jet boat

    Where did you read / learn about ---" airlocking " ---on this turbojet ?
  3. R

    Boating YouTube channels

    I used to sit at a launch ramp on weekends for entertainment.---50 years ago, no different today.
  4. R

    Dual fuel pump line diagram

    Fuel from tank goes to one pump.----Output from that pump goes to intake of second pump.----Output from second pump goes to carburetors.
  5. R

    Mariner 60hp motor identify help

    The motor in post #1 is not a ---LOOP CHARGED ---motor.
  6. R

    Evinrude 115Hp V4 Project Rebuild / Repowering a Fourwinns Fling Turbo jet boat

    Does your jet unit have a rubber impeller water pump ?
  7. R

    Ignition question (new to Suzukis

    Contact ----brownspointmarine.-----Long time Suzuki place.
  8. R

    New (Out of Box) BF20D Over Heating

    I know of a owner who used to run his 150 HP Mercury V-6 in his driveway.--Loved the sound of it.-----He was told repeatedly to use garden hose and muffs.----His reply was " I am only running it for 20 seconds or so , it won't over heat "
  9. R

    Engine won't reach max RPM under load

    Timing on these motors generally does not change.-----Adjusting and hoping it will run better may well lead to expensive damage.----Best to do some trouble shooting to find out what is wrong.
  10. R

    Need advice on power tilt for 1979 85 HP V4 Johnson

    I think it will.-----Read post #2 carefully
  11. R

    New (Out of Box) BF20D Over Heating

    It is possible that previous owner ran it without water to impeller.----There are folks that simply do not know this fact.
  12. R

    This coming out of 1975 Johnson 115 lower unit.

    Take starter apart for inspection and ohm check on armature.---Do not rush out and buy a new starter !!------Check battery cables.-----Slow cranking means you have weak spark.
  13. R

    Ran motor (in driveway) without oil in lower unit?

    Perhaps what is left over parts of the " shutter assembly "-----Sort of like a check valve to prevent water coming in the exhaust manifold.
  14. R

    1975 25 hp Evinrude 25502B

    Replace the reed valves.----It should then run like new.
  15. R

    Mariner 60hp motor identify help

    I missed those numbers.----135 PSI ( 95 X14.7 ) is good compression.
  16. R

    Mariner 60hp motor identify help

    Do a compression test before spending too much time or any EURO's on this motor.
  17. R

    Mariner 60hp motor identify help

    Your motor uses the 18-3007 impeller.----And if you take the old impeller out you will likely read the part number on it.-----Ends with 83 if factory impeller !!!
  18. R

    Mariner 60hp motor identify help

    use---google----mercruiserparts.com-----find your motor.------find part # for kits.-----google those part numbers.----done
  19. R

    Mariner 60hp motor identify help

    ??----Serial # is used to get the correct parts !-----And 98766 is a casting # and not a serial # at all.----Your location ?-----There must be a Mercury dealer that can help you !
  20. R

    Mariner 60hp motor identify help

    To me it looks like the powerhead has been replaced with a Mercury unit.----Compression test before you spend a dime on this motor.----New impeller before you launch the boat.-----Serial # on block is for an 89 model.-----Serial # is used to order parts.
Top