Search results

  1. R

    Top piston worth replacing? (120hp low compression)

    RTV is not to be used where there is gasoline present.----Simple as that.----Put a lump of cured RTV in some gasoline and see what happens.
  2. R

    NO START AFTER LOWER UNIT REPLACEMENT

    There were changes made in the area of the splines on the crankshaft.----And yes when you install the lower unit of a newer motor there will be a problem.----So if you back off the lower unit bolts 2 turns the motor turns easily by hand ( sparkplugs out ) and it jams when you tighten the screws ?
  3. R

    1963 Johnson QD-24B

    Perhaps explain in more detail what the issue is.-----Recoil spring not retracting the pulley ??----Or pawl not engaging the flywheel to start motor.----We are not looking over your shoulder.---Explain stuff.------I rebuilt a 1963 10 HP a few years ago for the 8 year old grandson.----He started...
  4. R

    1963 Johnson QD-24B

    Agreed----No lube on the spring and in the groove.
  5. R

    1960 Merc 400 shift shaft trouble

    Fact-----These things are easy.-----You must understand that the clutch dog is spring loaded.-----When you take it off in neutral it usually goes into forward when you bump the lower unit.------So.----Make sure the lower unit is in neutral as you slide it up.----Or make sure control is in...
  6. R

    Can't get boat even on bunked trailer.

    I put the rear roller in the water.-----Start pulling the boat on the trailer.----If effort gets to much I back trailer in 5 or 6 feet.----Repeat as needed.----Put my 30 ' Scarab Sport on the trailer with no help.----Folks sometimes offer help , but I say " no thanks " and boat always sits...
  7. R

    1996 Evinrude E88TSLEDR - Overheat - Starboard Side Not Flowing Well

    You have to be really careful with internet presenters.----One was trying to take a V-4 apart and was hammering taper pins in the wrong direction.----Then on another video he was trying it on a V-6.------I learned about these broken rings back in about 1980 and I can rebuild one without looking...
  8. R

    Omc identification

    ??----It appears to me that this crack is due to water in the gearcase or a passage way..----It froze and cracked the case.----Pressure test this gearcase.-----If it fails you need to take it apart for inspection.-----I assume you just bought this boat.
  9. R

    1975 115 2-stroke inline 6 WOT problems

    I remember people complaining about filters on outboards looking empty 50 years ago.---Motors ran just fine.-----Just the way it is I think.
  10. R

    1986 90HP Crossflow Johnson - RPMs increase at WOT when steering

    Lower the engine as needed and test run.
  11. R

    71 Johnson 50 50ESL71S clicking when going into reverse

    No damage done with the wrong oil.-----The oil pressure does the shifting.----Reverse requires the highest oil pressure to compress the spring on the clutch dog.-----So this machine has a strainer screen in front of the oil pump.----This screen has been known to disintegrate.---Possible damage...
  12. R

    1975 115 2-stroke inline 6 WOT problems

    If motor keeps running with the manual fuel pump you need to go over the entire fuel system.----Starting with screen in the fuel tank.
  13. R

    Safe to tow with bow not resting on front roller?

    In a high speed collision situation stuff will break.-----On my project the bow eye was anchored with a small block of wood.----That wood was rotten and come out as powder.------Replaced with solid glass with a second bow eye to boot.
  14. R

    Omc identification

    Time for a full tear down and inspection I say.
  15. R

    1996 Evinrude E88TSLEDR - Overheat - Starboard Side Not Flowing Well

    Yes that is what you are looking at.-----Properly done your grandkids will be running this motor.----These motors are scoffed at by some.----But seeing it was running with that kind of damage means that these engines are well built with just one flaw.----That being the design of the top piston ring.
  16. R

    Omc identification

    Cable disconnects up at the top / rear of the motor.----Post picture of cracked area.----Recommend inspection for rust damage if water was in there and exposed to oxygen !!
  17. R

    1975 115 2-stroke inline 6 WOT problems

    The bulb does not stay hard once motor is running, very normal.
  18. R

    Omc identification

    That would be the 400 model.-----Careful with that cable.
  19. R

    1996 Evinrude E88TSLEDR - Overheat - Starboard Side Not Flowing Well

    No point going any further.---Classic broken rings syndrome.-----Motor needs to come apart to replace with o/s pistons.---4 of them.
  20. R

    79 Merc 70hp Problems

    ???----Is that the date you signed on to this forum ?
Top