Search results

  1. R

    OMC p/n 0335626 (nipple, fuel & oil) purpose?

    I know where the part goes.-----It is easy to bypass that.--Parts is listed as available on one site $30.00---evinrudeparts.ca----Might offer help.
  2. R

    Do I need a new block or small side case half?

    Poor man fix is to use glass plate and mechanics blue to determine if it is in fact warped.----If it is then a wee hammer might correct this flaw !!---These items are a matched set.----Machined as an assembly.-----There are lots of used blocks around.--E-bay is one place.------Your location ?
  3. R

    Oil mixture

    Model # of this motor ?
  4. R

    OMC p/n 0335626 (nipple, fuel & oil) purpose?

    Your location ?
  5. R

    1985 115 ELPT Please help!!

    ???---Sorry------I really think you need some math tutoring as 50:1 is less oil than 30:1.-----
  6. R

    1970 Johnson 6hp Problems

    Gearcase needs a seal kit.
  7. R

    5.5hp Evinrude pressure conversion issues.

    You can not use that nipple ( as is ) on the intake manifold to run that mikuni fuel pump.
  8. R

    1985 115 ELPT Please help!!

    It will be a 2 stroke.---Mix gas and oil at 50:1 ratio.----When you buy a used boat or motor you have to put a new water pump impeller in the lower unit.
  9. R

    2000 Mercury (Tracker) 125 2+2 motor making gas slicks in idle

    They built these motors for quite a few years.-----Mercury normally does not keep building stuff that has major flaws for very long.
  10. R

    5/32 inch or 3/16 inch fuel line? 1986 60 hp Johnson

    I tried using 3/16 for carburetor feeds.----Persistent leaks.----Bought 5/32 line along with factory tywraps meant for hose.
  11. R

    1989 Force 35hp fuel pump issue

    These pump work with a PRESSURE pulse.---Perhaps refinish the pump housing.----Piece of glass and some 220 grit paper.---Might do the trick.
  12. R

    Is it safe to weld a winch post to the coupler?

    Find the proper trailer.---As it is now it is disaster looking for a place to happen.
  13. R

    1968 9.5 IDLE ADJUSTMENT knob

    Pull the shaft out !!---Need to inspect the bearing surface above the spline.----Post picture of area above the spline.-----Easy as it will slide right back in.
  14. R

    9.9 throttle sticky

    Needs a new bushing and perhaps a shim washer on the handle side.
  15. R

    What Is this fitting/fixture for?

    I thought it was simple !
  16. R

    What Is this fitting/fixture for?

    It is clearly identified as an OMC supplied part.
  17. R

    1971 18HP Evinrude Fastwin

    No offense but how did you conclude that motor ----" sounded dry "-----I am puzzled.----You are aware that plugs laying on the block can show spark, but when in the cylinder with 100 PSI air the will not fire ??----Testing / inspection / trouble shooting must be done.
  18. R

    Hard Start 15 hp

    Turn handle all the way to bump up against neutral stop.-----Remove cover and look for it.-------Ignore iffy marking on the throttle grip.
  19. R

    84-86 75HP Mercury.

    Your motor runs on all 4 cylinders ALL THE TIME.-------It was the later 4 carburetor ( 2+2 ) models that did not supply enuff fuel to bottom 2 cylinders at idle.-----Sounds like you need to look at bottom carburetor again.--Does spark jump a gap on all leads 3/8" or more ?-----And stop running...
  20. R

    Hard Start 15 hp

    Motor should fire right up then.----Trouble shooting required on your part.----Are you advancing throttle to the neutral stop or going by the " iffy " marking on the tiller handle ?
Top