Search results

  1. R

    1976 Johnson 25hp

    It should lift / pry off using 2 hefty screwdrivers.
  2. R

    1976 Johnson 25hp

    Remove ( lift off ) the cam.----Get a new factory key.----Re-assemble.
  3. R

    1980 85 hp evinrude starting problems

    Some will argue.----Remove bypass covers for inspection of pistons and rings.----No point wasting time and effort if motor needs rebuilding.
  4. R

    New to me '96 Evinrude 200, keep the VRO?

    Well ----if motor is laying on a pallet it is a bit heavy to stand it up.----If pump is on the bottom is might not be easy to check it out.
  5. R

    1980 85 hp evinrude starting problems

    What is the model # of your 1980 ?--85 HP.----I thought those had the electric primer.----If in fact yours does have choke flappers then adjusting the solenoid might help.
  6. R

    1980 85 hp evinrude starting problems

    So with the 4 sparkplugs left in , does the spark jump a gap of 3/8" ( 1 cm ) on a testing device.----I would like to see compression of 120 PSI on those.----But perhaps remove the bypass covers on the cylinders that is showing some scoring.----The trouble shooting has to be done by you.
  7. R

    1980 85 hp evinrude starting problems

    Are you pushing the key in while cranking it over ?----Are you advancing throttle while cranking ?-----And load test your battery.----Inspect starter brushes.
  8. R

    Bravo 3 Drive Showers

    Google----Thermax -----Stickers.------Likely others available too.
  9. R

    Bike tires

    I know that sunlight will damage rubber.-----Heat will harden rubber.-----Fluorescent lighting in say a 24 hour warehouse will damage / crack o-rings too.----Radioactivity will harden O-rings / rubber gaskets.
  10. R

    Does a Mercury model 200 (1978) 20hp have a kill circuit

    There will be a stop circuit.-----You have to be careful just starting a motor because you want to hear it bark and roar.----If there is no battery properly wired in then damage to the charging system may be the outcome.
  11. R

    Bravo 3 Drive Showers

    There are temperature sensitive stickers you can put on the drive.----Will tell you what temperature the drive is running at.
  12. R

    Questions about waterlogged foam on 1977 Mckee Craft

    Using the expanding foam is a fast / cheap method of producing a boat.----Took the motor off a " whaler " a few years ago for that very reason.-----Foam was waterlogged.------Boat went into one of those tub grinders and was destroyed in seconds.
  13. R

    V--12 and 600 ponies

    Seems like the uber rich will power with these.-----Coming to the haulover inlet soon I think.
  14. R

    87 15hp (J15ECUD) No power under load.

    They all rev up in neutral.-----They will do that with one cylinder not working.-----Test compression.----Test spark.
  15. R

    1980 KMV

    A " heavy " boat might be a concern to me.------Does this boat have foam floatation, I think it does ?---Possibly water logged ?----Water in the oil pan would be a concern.-----Think rusted / corroded parts.
  16. R

    Questions about waterlogged foam on 1977 Mckee Craft

    Once the foam is water logged it is near impossible to get the foam dried out.----Cut the liner.---Remove the foam.-----Choose a method other than foam to provide structure / floatation.----Doing a project myself.----No way that I am putting foam under the floor.
  17. R

    Another VRO Question

    The pulse limiter does nothing.-----It only closes to protect the VRO from high airflow / pressure pulse from the crankcase.----The large plastic VRO pump pieces would crack / blow up from a pressure spike !!!!-----The pulse limiter is not needed for a conventional pump since the parts are...
  18. R

    Another VRO Question

    The pulse limiter is a ---FLOW FUSE-----It only closes when there is too much flow of air from the crankcase.-------The pulse limiter is also NOT a check valve.-----It has nothing to do with amount of oil pumped either.
  19. R

    Hydrofoil or Trim Tabs??

    Working on an ---Action Marine 17 --Look for them on U-tube.---When spring comes again.----All wood taken out of transom and floor , and replaced with composite material.-----With 150 HP at the propshaft it will be very quick I expect.
  20. R

    Hydrofoil or Trim Tabs??

    Fact------A test I did myself.----Same 16' ski boat , same afternoon ,same tilt pin hole , same driver, same sst style props.----A 1970 model 115 Evinrude no power trim. -------19" pitch , great acceleration , maximum RPM 5800 , boat speed 54 mph.-----Then a 21" pitch , good acceleration, max...
Top