Search results

  1. flyingscott

    Help please! 1988 Johnson outboard lack of power and stalls.

    The roller needs to be replaced
  2. flyingscott

    2003 25 hp merc 2 stroke impeller replacement

    the factory manual tells you how to check timing. and also how to do the link and sync
  3. flyingscott

    2003 25 hp merc 2 stroke impeller replacement

    Get the manual and stop taking the bad advice you are getting.
  4. flyingscott

    2003 25 hp merc 2 stroke impeller replacement

    So put up a motor actually pulling those #s on a compression test. And a copy of the page.
  5. flyingscott

    Prop for McCulloch 14?

    Michigan wheel is a huge company. Look them up. And you have to find a place that specializes in props.
  6. flyingscott

    Prop for McCulloch 14?

    Michigan wheel made most of the Scott/McCulloch props. You might be able to get a hub for it. Call your local prop shop.
  7. flyingscott

    78 TO 82 115HP CARBURETOR SWAP??

    Aren't those different blocks? I thought the 99 cid block came out in 79? 93 cid blocks were 78 and before.
  8. flyingscott

    1999 Johnson 150 Ocean Pro Cooling Question

    How about you start your own thread and Not open a 10 yr old one
  9. flyingscott

    How much outboard motors have improved.

    So that crossflow 2 strk designed in the 50s gets better fuel mileage than a new 4 4strk?
  10. flyingscott

    How much outboard motors have improved.

    Seriously nobody is going to comment on the 3 gallons of gas in 4 hrs?
  11. flyingscott

    How much outboard motors have improved.

    You do realize how old that 4 cylinder design is don't you? And hard to believe it only used 3 gallons of gas in 4hrs of hard running. If your top Rpm at full throttle is only 4700-4800 rpm you might need a different prop.
  12. flyingscott

    Going Bravo Dual Prop on a Yamaha 250 2 Stroke?

    Yamaha made a duo prop 150 outboard. Maybe try to find one of those.
  13. flyingscott

    93 Johson 150hp fuel issue

    Get a good manual because the calibration pockets also need to be cleaned. Those carbs are not hard to work on. Factory manual ONLY!!!!
  14. flyingscott

    Outboard Valuation Help

    where are you located and is it a shortshaft?
  15. flyingscott

    1991 Johnson 175hp J175EXEIS Will only start and run using primer bulb

    O rings being bad makes no sense at all. If the orings were bad and the fuel pump good gas would be shooting everywhere. What is your compression? Do you have spark on all cylinders? The fact it only runs if you pump the ball points directly to the fuel pump. Fuel side rebuild kits are around...
  16. flyingscott

    Help please! 1988 Johnson outboard lack of power and stalls.

    Yes there is only one. That needs to be in 1 piece does it have a clear covering on it? Do both carbs move at the same time. Maybe time for you to invest in a factory manual.
  17. flyingscott

    Help please! 1988 Johnson outboard lack of power and stalls.

    Otherside of the carb is the throttle roller. Make sure it is in one piece
  18. flyingscott

    Help please! 1988 Johnson outboard lack of power and stalls.

    Doesn't that carb have a plastic top? And are the throttle rollers in good shape?
  19. flyingscott

    Help please! 1988 Johnson outboard lack of power and stalls.

    I am talking about the gasket on top of the carb. Not the float bowl gasket
  20. flyingscott

    very cool carb and intake manifold causing moisture

    Are you still doing this all in your Driveway? E 10 is fine to run in that motor no need to waste your money on more expensive gas. Racer is right about the gas cooling the carb down. And about the doing a link and sync.
Top