Search results

  1. J

    2001 yamaha 9.9

    Winterized kicker and had good tell tale. Just installed it back on boat and no tell tale...I can blow through the hoses except the top hose port. Also curious if I should get the wash fitting on the side. Will that push more water then using muffs. Not sure how it does not pump now
  2. J

    Mc-1 wont go all the way

    I've been fighting this leg for couple hours now. New engine installed...all mounts the same. I tried engine alignment tool however I don't think it's going all the way in.
  3. J

    Timing cover

    Good day. First issue with newford302 engine. The new timing cover does not have 2 bolt holes for alt bracket. It's already installed as well as the pulleys and water pump. Is there a bracket for alt that will bolt onto water pump and timing cover.
  4. J

    Ford 302 thermostat

    Good day. I am wondering on what to use for my thermostat. Boat has closed cooling. Any suggestions or a part number so I can get the right one
  5. J

    Temp sending unit

    I have bought a new unit however it is physically different . I am having trouble finding one that looks the same. The new one is what came up at parts store. Will it work?
  6. J

    Mercruiser bellows

    It's bellows time. What is the easiest order for install. The drive is mc-1 I believe we figured out in another post
  7. J

    Alignment tools

    I have bought this and I'm not to sure what's what here. No directions came with it
  8. J

    Closed cooling diagram

    I'm trying to find a picture of flow for my boat. 70's 302
  9. J

    Gasket

    I am trying to figure out how this gasket goes as I didn't remove it. I can see that it has oilpan shaped goop still on one half.
  10. J

    Oil pressure sending unit upgrade

    I would like to upgrade this old unit. 70s Ford 302. Is there a simple switch available
  11. J

    Alpha 1 gen 1 with v8

    I have been told I should put a smaller prop on my boat wich is a 23 foot campion cruiser fiberglass. It has a 19 on it now. I am putting in a new 302 and want to match prop. It was suggested a 16 or 17. Any input would help
  12. J

    2001 yamaha t9.9

    Has anyone a clue were this wire goes. I'm either really blind or something. I didn't pull it off
  13. J

    Ford 302 closed cooling system thermostat housing

    I have been looking all over the place to replace my housing and have not found the proper one. I have posted on here about it before and figured I'd try again. Here is a pic of the one I need.
  14. J

    302 ring gear replacement

    I have removed my ring gear as it has wear and engine is already out. Does it matter in wich direction the new one goes on
  15. J

    Ford 302 engine coupler

    I'm wondering if these are able to be tested. Mine looks almost new however I don't want to pull my engine out again if I don't have to.
  16. J

    Ford 289 intake manifold

    I have pulled my manifold and took the carb off. Put carb bolts back in and snugged them up. 1 bolt goes all the way through and the rest don't. Doesn't seem right to me
  17. J

    2 bottom bolt loops on y pipe broken

    I pulled my y pipe and the bottom portion of the two bottom bolt loops are gone. Is there a way to repair just those loops the bolts go through. The rest of the y pipe is in great shape.
  18. J

    Ford block id

    My block casting number is D20E-6015- ab. Wondering if it's 302 ...long block, short block?
  19. J

    1975 23 foot fiberglass with cuddy

    I am wondering about prop size for my old boat. It had a 21p when I bought it. I switched it to a 19. It's been suggested I run a 16 or 15. Does that sound right. Boat revs out at about 3500 ram for causing speed wich seams high to me
  20. J

    Electronic or points coils

    Good day...I was told yesterday from a fellow who said that electronic and points set up use different coils....any truth to that...I bought a flame thrower 40000 ..1.5ohm for my points system
Top