Search results

  1. jerryjerry05

    Replace kill switch or bypass?

    Your control/shifter is called : Remote Control-4000 Side Mount(Power Trim)(if it has power trim) The difference would be the non power tilt wouldn't have a T@T switch. The safety switch is : SWITCH ASSEMBLY 91941A8 about 25$ LANYARD ASSEMBLY 15920Q54 NLA but can be found on Ebay...
  2. jerryjerry05

    91 15hp Force/gamefisher conversion to points

    This post is a year old and the original poster doesn't seem to be on here very much?? You need to start your own thread. The change over: your best bet is try to find a 9.9/15 with points and use the parts from there. I imagine that most hard parts(timer base, plug wires, flywheel etc., your...
  3. jerryjerry05

    1994 Force 120 hp Shaft length?

    20 inch.
  4. jerryjerry05

    Lower unit does not want to come off

    I see the pics of the motor. That's NOT a 94 more like a 96-99 with the Mercury lower unit. If there's no screw under the trim fin then there are 5 nuts holding the drive on . Look up inside? If it drops any? then don't come down. The splines might be twisted and holding the drive in place.
  5. jerryjerry05

    Gear case cover

    Post a pic?? Why do you think it's bad?
  6. jerryjerry05

    1994 Force 120 hp Shaft length?

    Post a pic of the mid section including the lower unit.
  7. jerryjerry05

    Carbs leaking fuel 1988 force 125hp

    Is the idle tube loose? No? then I wouldn't worry about it. The pic shows foam floats, they don't usually go bad unless someone has hit them with something that melts the foam. The position of the float when the carb is upside down should be level with the body of the carb. The drop (float)...
  8. jerryjerry05

    '95 120hp compression test results

    14 just might be a record?? The exhaust cover wit all the 1/4-20 screws is were I break the most. That's why I NEVER remove the cover unless it's a complete rebuild. The heat and the cool down and then heat again tends to eat away the edges of the aluminum and then the gaskets don't want to...
  9. jerryjerry05

    Carbs leaking fuel 1988 force 125hp

    Top carb.Start at 1 1/2 turn out and adjust from there. If it doesn't idle maybe anther 1/2 turn out? The adjustment, motor warm, in the water and in gear. Turn the screw 1/8th turn in and wait 10 seconds, continue until the motor bucks coughs or stalls then out 1/2 turn. Then repeat on the...
  10. jerryjerry05

    70hp Force

    Yours does have a relief screw, on the bottom white screw. WD-40 or any penetrating spray, spray liberally. Turn to the left. I see a BIG problem, your boats growing black hair :)
  11. jerryjerry05

    1995 Force 120 missing

    Dave K Sent you a PM.
  12. jerryjerry05

    Carbs leaking fuel 1988 force 125hp

    They don't make them anymore, and the plastic is JUNK> Try Franz Marine or marine salvage yards. Ebay has carb sets but very expensive :(
  13. jerryjerry05

    '95 120hp compression test results

    First!!! those numbers across the board are low. With a good gauge they should be 145-155 maybe even higher, even a new gauge(Harbor Freight Tools) can give bad results. I think they started in 95 the 120 came from the factory with the top and bottom cyl. lower by 10# than the 2 middle cyl...
  14. jerryjerry05

    Lower shift rod came out of gear shift arm...re-assemble?

    No new seals needed. Just use sealer when needed?
  15. jerryjerry05

    Sputtering when at full throttle

    I can't get it to open??
  16. jerryjerry05

    Lower shift rod came out of gear shift arm...re-assemble?

    Yup, disassemble the lower and screw it back in. Find a parts diagram and use that for a reference, take pics as you proceed. You might find using assembly grease will help hold the pieces together while you assemble.
  17. jerryjerry05

    1992 Gamefisher Issues. Need help.

    The diaphragm in the pic is bad, it should be smooth and no swelling. Finding a new carb, nope. There's a used one on ebay https://www.ebay.com/itm/Vintage-Tillotson-Quicksilver-1300-F712061-Marine-Carburetor-In-Box-A2153/203343014419?hash=item2f58302a13:g:JW4AAOSwe95gY0zO But you probably...
  18. jerryjerry05

    Sputtering when at full throttle

    Helps to know what were working on? The carb can have 2 different needle/seat combo's. One needle can have a rubber tip and a solid seat, the other a solid tip and an o-ring in the seat. Some cleaners can hurt the rubber in the needle/seats and melt plastic if there's any used and can swell the...
  19. jerryjerry05

    70hp Force

    You can have one of three different styles.. A picture would really help.
  20. jerryjerry05

    2000 Mercury (Tracker) 125 2+2 motor making gas slicks in idle

    There's supposed to be a recirculation system on all outboards made after the 70's Some might not work as good as they should. There are tiny hoses that can get clogged and the unburned fuel finds it's way out. Start it and look at the front of the carb and see if any fuel is coming out the...
Top