Search results

  1. jerryjerry05

    Prop makes "clank" sound when shifting gears.

    You take the prop off? and then loose a part?? Missing a spacer?? Gear oil full?
  2. jerryjerry05

    Force 70Hp 1991 gear problem

    pnwboat is right about the pin being broken, looks real short. Year/HP/Model??? Depending on the year? the pics should work?? The pic below, #7 and #8 7 rides on #8 and stay's in place with a bit of Assembly Grease. The grease melts/dissolves quickly and the gear oil lubes it after that.
  3. jerryjerry05

    Hooked battery up wrong. No power to ignition

    There's a circuit breaker on the bottom of the bus bar(where the cable meets the motor harness) check for power there. Then the wires that hook direct to the battery, some have an inline fuse at the battery end. BUT!!! if you smelled smoke?? then you could have cooked the lead that supply's the...
  4. jerryjerry05

    Tilt trim

    IF?? your getting 300# that shows the motor/pump is working. Can you post a pic of the pump/motor? Was the pump used? if so the valves in the bottom might need replacing? The valves/seal are TINY,TINY and after time go bad, the link shows the seals...
  5. jerryjerry05

    Trim tilt gauge and sender unit install?

    When you get it, can you post pics of the sender and then pics when it's installed??Thanks!! I was really interested in this part and decided to look into it further. It looks like your 1988 might not be able to use this??? the parts fitment starts at 1994 and newer??? Seems there's a bunch of...
  6. jerryjerry05

    Mercury slowing down

    1995 Mercury 75 hp. 17ft.Ranger Alum. bass boat. I don't know how to set the timing and don't have a manual for the motor. The motor seem to runs good and hitting on all 3 cyl, The linkage/throttle is advanced as far as it can go. Yet the most it gets is 4100 rpm's and 30mph. at wide open and...
  7. jerryjerry05

    Trim tilt gauge and sender unit install?

    Where??
  8. jerryjerry05

    Chrysler Engines

    There's Franz Marine who might have those hard to find parts??
  9. jerryjerry05

    Trim tilt gauge and sender unit install?

    Good luck finding any of these parts. Myself, I've never seen a T@T sending unit. Someone might have them, maybe try Franz Marine, Mastertech Marine.
  10. jerryjerry05

    1966 Sea King 6hp idles ~ 10 seconds, accelerates then quits

    Recently, my work tank (the one I use on all the motors that I repair) failed me.:( I was working on a Johnson 25hp. (my motor) The squeeze ball wouldn't get hard, so I replaced the diaphragm, still wouldn't get firm, so I went through all the steps for repair. Found the squeeze ball was bad :(...
  11. jerryjerry05

    No spark

    Very rare the trigger is bad. The leads from the trigger might be the problem (see my previous post) but not the actual trigger. The stator would be my guess if the coils check ok?? UPDATE!! I gave you test things for a motor with Prestolite ignition. IF???? you have a points ignition??? then...
  12. jerryjerry05

    1986 Galaxy OMC Outdrive Gears

    86 was the year they introduced Cobra but they still had some stringer drives used that year. Pictures are worth a thousand words.
  13. jerryjerry05

    Hose under engine open??? Please help

    Any gear. But when installing. in F That way you can turn the prop and the splines align and the drive goes back in easily.
  14. jerryjerry05

    Pulling outdrive question????!!!

    IF???? you drain the gear oil??? make sure you fill it from the right place!!! They fill from the side of the drive about 1/2 way from the top down. If not filled properly, the drive will self destruct and cost lots of $$$
  15. jerryjerry05

    No spark

    You try swapping the coils around? These coils can be bad but in all the years I've worked on these motors, I've only found a couple to be bad. The trigger has very thin wires that breaks under the shrink wrap at the connector, try gently tugging on the wire and see if it comes apart...
  16. jerryjerry05

    Upper drive shaft bearing two piece unit

    Is your From what the manual says , the "lower driveshaft bearing" doesn't need to be shimmed, assembly grease for the bearings. The following link is for assembly grease...
  17. jerryjerry05

    1988 50hp Force coil pack to cylinder order

    Ebay there's 3-4 on there now.
  18. jerryjerry05

    1988 50hp Force coil pack to cylinder order

    Get the FACTORY manual. for a 1988 The huge backfire is probably the coils were backwards or there was an over fueled situation(flooded). Did you bother to do a compression test? These 2 cyl. motor can start and run on 1 cyl. not great but they do run.
  19. jerryjerry05

    So I've got a bit left over...

    Not in any lower I've ever seen or in any part of the motor????
  20. jerryjerry05

    Tools required for lower unit reseal

    Just use a sealer on the mating surfaces of the new seals. Use grease or something like Anti-seize on the bolts. Then do a pressure test. You can find U-tube video's on how to make a pressure tester.
Top