Search results

  1. T

    1988 Evinrude 120 V4 -Suddenly going into SLOW Mode at WOT. Video included

    Not that this is going to help your problem but just out of curiosity what type of tac are you going by? Maybe it’s not all that accurate.
  2. T

    johnson 70hp 2 stroke 1995 shut down when warm

    It might be worth your time to use another gauge and compare the numbers. If they are still no good pulling the head and doing an inspection will tell you a lot about what’s going on.
  3. T

    2000 Johnson 15hp wont pump water

    Best of luck. I hope they get you up and running soon. I wouldn’t be surprised if they find the fins of the old impeller you mentioned were missing causing some blockage. Keep us posted. Best
  4. T

    2000 Johnson 15hp wont pump water

    What did you mean by your seeing a lot of water coming out around the pump housing? Did you have the lower off and were testing with a drill in a bucket when you saw this? Do you recall what the rest of the pump looked like when you changed the impeller? Was the wear plate and cup if it has one...
  5. T

    johnson 70hp 2 stroke 1995 shut down when warm

    Agreed with above. Has the water pump been serviced since you bought it. That’s always the first step to a new to you motor if it’s age is unknown.
  6. T

    1987 Evinrude 110 success

    As they say there’s more than one way to skin a cat. Glad everything worked out out for. Time to enjoy the fruits of your labor.
  7. T

    Fuel issue please help !!

    Are you saying you didn’t remove the slow speed/idle needles when you cleaned the carbs?
  8. T

    Engine will not stay running without choking

    Luke 84 You would be better off staring your own post. Talking about 2 different motors on the same post is gets confusing. Thx
  9. T

    Engine will not stay running without choking

    I once watched a guy spray the outside of the carbs down and explained to me he was doing a carb cleaning because it wasn’t running well.
  10. T

    1991 20HP Evinrude no acceleration

    Yep that’s what a spun hub looks like. They can be repaired but it’s likely not going to save you a ton of money. Glad you finally got this resolved.
  11. T

    2000 Johnson 15hp wont pump water

    If you were getting water out of the tell tail while on the hose it’s not likely that’s where the problem lies. The tell tail passages don’t circulate through all the water passages. First check to be sure the pump service was done properly and the key is in place. If you wanted you could drop...
  12. T

    2000 Johnson 15hp wont pump water

    Agreed if it was missing fins they are properly jammed up somewhere. The hose pressure may have been enough to push water to the pisser.
  13. T

    Evinrude Fastwin 18 No Full Tilt Lock

    Yea 11” is all good until it’s not. 😂 There are many ways around this as mentioned with some being cheap or free. Best
  14. T

    Evinrude Fastwin 18 No Full Tilt Lock

    If all else fails you could use a transom saver to hold it up.
  15. T

    60HP 1989 Johnson outboard low compression

    The assembly grease will help you keep the needle bearings in place durning assembly. Without it you may end up going insane.
  16. T

    Oil leak

    Well said. Far better than my version. The oil question was meant to be separate and I was just curious if maybe extra oil was being used but clearly not. I need to work on using my words.
  17. T

    Oil leak

    Buy the look of the staining on the paint it could be running a bit rich as well which would make this dripping heavier than normal. Just out of curiosity how much oil do you use per gallon or liter of gas?
  18. T

    25 horse Evinrude eTec Stops Running

    I don’t know squat about the Etec technology but there has been a lot of chatter on here about the power pack or equivalent over heating. Do a bit more looking around through old post and you will find lot of talk about it on here. Best
  19. T

    1969 Evinrude 25hp 25903D points issue

    I know I have replaced condensers due to a request and ended up put the old ones back in because the new were no good. It’s definitely worth looking into if you replaced them. I can’t remember if you said you did or not. Bad case of CRS this morning.
  20. T

    1991 20HP Evinrude no acceleration

    Cotter pin for the nuts is correct. I guess I should be more specific next time
View older results
Top