Search results

  1. S

    1991 25hp evinrude starting issues

    Yes, my 83 has that service bulletin but I figured by 91 it should have been fixed. Nothing to do with air really they just want the timing moved up before the carb starts to open. Before doing that on mine it would run but hesitate before taking off. Hope that works for you.
  2. S

    1994 40hp Johnson run

    Yes I hear it. A wire is sparking somewhere. Start it after dark. Probably why it's missing.
  3. S

    1991 25hp evinrude starting issues

    Have you looked at your primer system and is it working correctly? Not the primer ball. Are you letting it warm up properly? Maybe when it running, pull each spark plug wire off at a time and see if it dies..... You might be having a problem with one cylinder or something.
  4. S

    Evinrude 25202r WOT adjustment

    You know I'm not quite sure about your link and sync on that older motor. Maybe that one doesn't have that rod....my 77 does. Must have something. Your motor new was probably 140 psi and you would hope it to be no lower than 110ish. My 77 is at 125. Hopefully someone will come by and show...
  5. S

    1991 25hp evinrude starting issues

    Get one of these and set it to 1/2inch. Nice blue spark.
  6. S

    Evinrude 25202r WOT adjustment

    If the butterfly is perfectly flat when you twist it to full throttle while in gear than your carb is set correctly. You may want to check compression with another gauge just to be sure. Compression is low.
  7. S

    1991 25hp evinrude starting issues

    Define good spark. Idle jet setting?
  8. S

    98 Johnson leaking hydraulic fluid.

    Here's what your up against. Enjoy.
  9. S

    Evinrude 25202r WOT adjustment

    Not ex Not exactly sure on that year but what your describing is the proper way of adjusting the idle/timing which is done at the carb. The adjustment for wide open throttle is done under the flywheel on the port (left) side. There is a long rod with a set screw and that controls how far the...
  10. S

    98 Johnson leaking hydraulic fluid.

    Looks round to me so I don't understand.
  11. S

    98 Johnson leaking hydraulic fluid.

    They make a driver with longer bits at HF.
  12. S

    Remote throttle/shifter + steering for 15HP tiller steer

    Here is a video of how that works and a different one I've never seen.
  13. S

    Remote throttle/shifter + steering for 15HP tiller steer

    https://www.defender.com/product.jsp?id=1054937
  14. S

    Remote throttle/shifter + steering for 15HP tiller steer

    I believe it locks down once you have it adjusted but it's been a long time since I played with one. Had one years ago on a 25 HP Johnson.
  15. S

    Remote throttle/shifter + steering for 15HP tiller steer

    Here is a better picture of the concept.
  16. S

    Remote throttle/shifter + steering for 15HP tiller steer

    Your motor being a tiller model doesn't have a tilt tube for the steering cable to go through. There used to be a model the bolts to the transom and then grabs the motor handle. I see you have the hole at the end of the carting handle. Could find the whole kit but it must be out there. Here is...
  17. S

    1992 Evinrude 150hp EXEN will not run correctly

    Compression test? Did you try pumping the primer ball?
  18. S

    Yamaha F100 TLRY - 2 lower units but only one shaft fits?

    Is the one that goes in a different taper at the top?
  19. S

    Yamaha F100 TLRY - 2 lower units but only one shaft fits?

    Yes, it's not right. You can't beat a SQ peg into a round hole. Have you thought about swapping the shafts?
  20. S

    Yamaha F100 TLRY - 2 lower units but only one shaft fits?

    Not sure on your motor but I have swapped driveshafts in lower units where the top is different but the bottom was the same.
Top