Search results

  1. flashback

    Pumping lake water into water holding tank

    Why? you could just put a thru-hull fitting in and hook the pump to that and get water anytime you need it. or even hang the pump over the side when needed plus you could take longer showers.. I get what your wanting just leave the holding tank out of the game, it will get nasty.
  2. flashback

    Gimbal bearing mystery

    That's what I understand Joe, I was able to get a greaseable one which is what I wanted, but after taking the old one apart, now I'm not so sure. I think it would be best to grease the bearing with the engine running so at least the grease could get worked into the bearing while under pressure...
  3. flashback

    Gimbal bearing mystery

    I recently changed the gimbal bearing and being the curious sort I took my old bearing apart. The tolerance ring has a gap in it that aligns with a hole in the carrier which in turn aligns with the grease fitting on the housing. When I removed the bearing from the carrier I found a channel...
  4. flashback

    Voids found after new transom install

    Years ago I was able to get empty caulk tubes from west systems epoxy. They work well.
  5. flashback

    Dead rise question

    I have a 220 signature and it is a tank. weighs 4000 lbs dry. I'm just getting used to it. (just got it running a month ago).. I don't get large waves on the lake I'm on unless it's wake from other boats but it handles the chop pretty well. It has a decent running 5.7 in it and in my opinion...
  6. flashback

    My boat sank, part II

    Maybe you could use a trash pump to dig it out? At least a hole for the drive so you could start it. Best of luck man, Finding a trash pump in NOLA would probably be very hard at the moment..
  7. flashback

    new carb new issue

    When this sort of thing happens to me I generally find the last thing I was messing with is usually the problem. Also 180 temp is a bit warm.
  8. flashback

    Blower fan and Bilge is NOT working. Help

    That's where the breaker is on my 95 searay. right under the switch.
  9. flashback

    Never underestimate the power of the mechanical fuel pump

    Did you figure out what caused the increase?
  10. flashback

    Screw Hole Repair / Below Water Line

    If there's no wood involved your patch will probably last forever. Marine tex might have been a better choice if your hull is white.
  11. flashback

    Is talormade curved windshield really glass?

    I used a razor blade and some windex and it worked out fine. The windshield is indeed tempered safety glass and it's nice and smooth now..
  12. flashback

    Stuck Valve/Cracked Head/Cracked Block

    If your engine is like an old 350 I had, rocker studs are press fit so be sure the stud didn't slip.
  13. flashback

    mercrusier 350 MAG MPI coupler problem

    I had the same question a few weeks ago, the splines don't go the entire length of the coupler.
  14. flashback

    Fuel Pump Diaphragm Rupture Hose Type?

    A couple of months ago I converted to an electric fuel pump and removed that hose and if I remember it connected to a small brass fitting that is pressed into the carb body just below the top edge of the carb.
  15. flashback

    Is talormade curved windshield really glass?

    Ha, we must have met at some time, you know me!
  16. flashback

    Is talormade curved windshield really glass?

    It's the 95 sea ray. I just didn't want to take a razor blade to it if it's not glass. Most likely the paint is 2 part epoxy picked up in a boat yard somewhere. It's not too bad but you can feel it, I'll pick an inconspicuous spot and experiment. Probably try some spirits first and maybe some...
  17. flashback

    Is talormade curved windshield really glass?

    They seem to advertise it as glass, but before I try to clean off some paint overspray that it gathered sometime in the past it would be good to know what its made of.
  18. flashback

    Outdrive gasket pushing out

    I can relate to that, I recently replaced the SS wire rope on a boat lift and thought I could re-use the old clips. Wrong! When I tried to loosen them every one locked up. Had to get new clips..I'll know next time..LOL
  19. flashback

    Steering maintenance

    If I were doing the evaluation service points would raise the score! My boy has an MTD riding mower and it needs a blade spindle,why... No grease fitting for the bearing. My truck has a noisy wheel bearing, why... I can't re-pack it. But the spark plugs sure do last.
  20. flashback

    Steering maintenance

    My only experience of "feedback" has been with PA systems and guitar amps. thanks for clearing that up for me. Mainly I am looking for any lubing or adjustments that might be available Like greasing the rack mechanism or cable and adjustment procedures if any. I don't have a manual on Teleflex...
Top