Search results

  1. flashback

    Time to reassemble

    LOL, good answer! I won't either, this boat will live most of it's remaining life with the drive down and if the cable goes south a bit sooner then I will know where that bit goes next time and how to get it there. The fella doing the video in my opinion was a bit off, the grommet is there to...
  2. flashback

    Time to reassemble

    wow I just read my last post and it didn't make much sense to me either. I was pretty hot and tired. There is a plastic grommet that I assume snaps into the transom on the inside to protect the cable from chaffing where it goes into the gimbal housing. should it have gone on the outside of the...
  3. flashback

    Buffing the hull

    No way I will sand it with any thing less than 1500, gel coat is thick but not that thick.
  4. flashback

    Buffing the hull

    I here ya, I
  5. flashback

    Buffing the hull

    LOL, sounds like nothin changed,
  6. flashback

    Buffing the hull

    This process is not new to me. 30 years ago I buffed many using 3M heavy duty compound with a wool pad, but times change. That said, if there's a better way these days, I'm all ears!
  7. flashback

    Time to reassemble

    That is how I believe I have it, i have the same pic in the manual i downloaded. I should stop second guessing myself. How bout that grommet? I suspect the cable will suffer. Bolted the leg on today and it went well
  8. flashback

    Time to reassemble

    Used a weed eater line for a guide to install the cable but I think the old cable routing may have been wrong, it came up and over the starboard engine mount and did not go in front of the exhaust but directly behind the steering gear and then to the shift plate. So I re-routed it under the...
  9. flashback

    Time to reassemble

    I'd be happy to even if you don't need to fix it. The bass have been good on the river this year! I still have a kayak if my shade tree repairs go south. Thanks for helping!
  10. flashback

    Time to reassemble

    I installed the gimbal housing today and again the water hose was a struggle but I think it's good. The main bellows was not too bad and did not use any glue at the gimbal housing end so if it leaks Rick is gonna fix it..LOL. I used an empty 1qt paint can to set the aluminum ring. It fits...
  11. flashback

    RPM gauge not hooked up

    keeps the hours down if your tach has a hour meter.
  12. flashback

    Engine won’t rev past 2500 rpm and vibrates

    Guess i should add, only one at at a time, if idle changes, its good, plug it back and go to the next. If you pull one and no change you've found a problem.
  13. flashback

    Time to reassemble

    I decided to blow off new senders. Haven't had this boat long enough to know and I don't really care. Put a thick coat of silicone on the bare wires and if they work great. When I took the drive off I couldn't lower it completely, will that cause any problem when I put it back?
  14. flashback

    Engine won’t rev past 2500 rpm and vibrates

    Pull one at a time and listen for a change in the idle.
  15. flashback

    Engine won’t rev past 2500 rpm and vibrates

    Might be running on 3 out of 4. Pull plug wireswires
  16. flashback

    Courtesy lights to LED. Dropped the wires for one light.

    Might try a piece of hose taped to a shop vac. Might work
  17. flashback

    Time to reassemble

    Thanks to both for the info. I will get some #3. I don't wrench enough to keep the stuff around, it always goes bad by the time I need it again. The last project I had was rebuilding an antique clock movement and all I needed for that was some good oil and a lot of patience. LOL I've come to...
  18. flashback

    Time to reassemble

    LOL! Well now that we have that sorted out, what's a good substitute for merc's perfect seal for the threads on the shift cable. seems like teflon tape would work on that, and I have plenty of it laying around.
  19. flashback

    Time to reassemble

    Dis -assembly went easy, I just cut every thing made of rubber and thru it away. one of the hinge pins on the ring was hand tight and the other not much better so that was a surprise. anyway I got my new parts and just need to do a bit of cleaning and I am ready to put things back.. Got a...
  20. flashback

    Engine coupler woes

    Thankfully a false alarm, I have a hunting friend who loaned me his bore scope and I have plenty of splines and they all have flat tops. The gimbal bearing was so trashed that paranoia set in. I have some high pressure moly graph grease which I use on my lift gear which seems like a good choice...
Top