Search results

  1. C

    1988 48 special carbs

    clean the carb incl top idle chamber nothing wrong with jets except crud
  2. C

    Fuel primer inop

    if it does not work electrically have you tested the ohms across the 2 wires controlling it. it is basically just and an electro magnet controlled valve so you better not see OPEN between the wires. see video if the failure to let fuel go by while under pressure is not...
  3. C

    Evinrude Big Twin 35

    Leroy's will give all the basics to service the magneto tons of info also visit DUckworks https://www.duckworksmagazine.com/06/columns/max/articles.htm Reviving a Vintage Big Twin Part 1 Part 2 Part 3 Part 4 http://www.leeroysramblings.com/#12_OB
  4. C

    2001 fitch 90hp

    see manual 2002 and up but... it may help with some trouble shooting like ETECs FICH has a VST and likely... it may have a small conical filter on the return fuel line from injectors and..... they do get clogged with fuel line crumbling pieces and cause grief VST fuel barbs...
  5. C

    Evinrude Big Twin 35

    https://www.duckworksmagazine.com/04/s/columns/max/15/index.htm
  6. C

    Evinrude Big Twin 35

    visit the AOMCI's site "ask a member" where oldies get fixed up DO NOT JUNK IT!!! https://www.aomci.org/forums/forum/ask-a-member-d1/ Join up and get a free 400 page + service manual to pamper your big twin
  7. C

    Source for power trim switch on older Evinrudes?

    momentary single pole double trhow switches are made in all sizes ( maybe not yours exactly) maybe you can fit something close enough search AMazon MC MAster etc.....
  8. C

    Impeller replacement schedule

    Agree... some stuff is cheap but....I can't say that I have yet to read that many horror stories of impeller causing catastrophic damages, after reading thousands.... posts from 3-4 sites across 20 years . But I agree yes...horror stories do happen ...from neglect more likely...
  9. C

    surging issue

    best to clear the "hotter" issue asap. impeller ??? tank venting ok ??? open the fuel cap carb (s) clean ?? running pre-mix ?? why not fix the oiler issue ??
  10. C

    Rope Starter Eyelet 6/8hp.

    carefully drill it out or cut it with a dremel tool or small hacksaw blade... from the back side
  11. C

    Impeller replacement schedule

    Dry runs in the driveway probably kill more impellers than years of looking for fish. my 75 ETEC probably has had 3 impellers in 17 years and all looked fine when replaced... did them anyway to be safe .an ounce of prevention is worth a pound of cure :-)
  12. C

    Impeller replacement schedule

    all depends on hours/year of use & the quality of the impeller I have seen some lasting 10 years + but to be safe 5 years sounds a good mid point. Some swear by 3 years . This should be an interesting thread.....
  13. C

    Setting points on 50's-70's Evinrudes with a meter

    I notice the Honeytek works on a 9v battery. Unless the meter has a built in voltage booster to reach 275-300 DC which I doubt it would be incapable of testing an outboard capacitor in a simulated mode of operation. it may tell you a uf value or a dead capacitor but it woul be unable to...
  14. C

    Setting points on 50's-70's Evinrudes with a meter

    basic VOM style meters with capacitance will give you the capacitance value (if not open or shorted) using an internal meter battery of maybe... 9v you did not tell us what meter you purchased . Testing capacitance at 9V will not test the capacitor's tolerance to high voltage kicks...
  15. C

    Mystery hole evinrude 70

    pea size JB weld will take your worries away
  16. C

    jack plate wiring

    great now buy some relays and hook it up properly so you don't make needless sparks and blow something expensive !
  17. C

    Setting points on 50's-70's Evinrudes with a meter

    throttle position is not important no matter where the throttle position is at.......... the points/will always begin to open when the piston reaches TDC . just follow this video and all will be fine. the high point of the cam lobe will just....open the points at TDC if adjusted per...
  18. C

    jack plate wiring

    relays are there to carry high current loads that common switches can't otherwise the arcing will eventually burn the contacts or worst...weld them shut relays allow you to control the transfer of these high currents without looping to/back from console switch positions. you need...
  19. C

    Evinrude 2hp Issues

    Looks doesn't mean to much so like the man said... Trust but verify.... btw my brother had one of those 2hp.....check the carb body for air line cracks !!
  20. C

    Evinrude 2hp Issues

    sparks tested ok but.... after a while sometimes the capacitor or coil can start to act funny. Unless you have a proven good capacitor assume it needs to go ...and replaced. inspect the coil for burn marks . best yet take everything apart (mag plate) and change the pulg wire with a new...
Top