Search results

  1. C

    1990-1995 era 3 cylinder charging capability?

    if your boat sits ouside much you may want consider a solar panel to trickle charge the trolling battery
  2. C

    1994 40hp Johnson run

    that is what I call a waker upper ....!
  3. C

    You were right , she's a runner

    in my country you need a boat operator permit (unless it is a canoe or row boat ) and most idiots get it by passing a test behind a keyboard via Internet and if you can't read ,write or type your buddy can fill in the blanks for you.
  4. C

    1992 Evinrude 150hp EXEN will not run correctly

    slow mode aka SAFE mode on ETECs ...did that exist in 1992 ??? if so.... what triggers SLOW mode...best to find out as it will point the way to happiness
  5. C

    Points open to .035

    to check for sparks just use a drill to spin the fw while you ground the sparkplug to the engine body to at least confirm the presence of spark but an adjustable gap tester is even better has uggested. Suppose I should have ordered plug wires?... yes you should install new 7mm metallic...
  6. C

    Will Replacing Rings Increase Compression >105PSI?

    Engine runs really well but is slightly underpowered. hum... will a ring job provide a cost effective solution on a "really well running" 32 year old engine.
  7. C

    Will Replacing Rings Increase Compression >105PSI?

    are you having problems with th eengine ? is the gauge OK and accurate ??
  8. C

    Evinrude 7520 clearance question

    if you plan being addicted to oldies you should visit AOMCI ask a question board...where oldies are pampered :-) https://www.aomci.org/forums/forum/ask-a-member-d1/
  9. C

    Parts manual evinrude/johnson 7.5

    try this https://www.aomci.org/forums/topic/1956-johnson-ad-10-m-parts-list/
  10. C

    98 Johnson leaking hydraulic fluid.

    I find that a 1/4 inch impact screw driver works wonders on stuck bolts and screws start slow....
  11. C

    1992 Evinrude 150hp EXEN will not run correctly

    deleted
  12. C

    Lower unit oil

    I think BRP uses US size 5/32 Allen on OEM ...but I have managed to strip them. boils down to preferences I guess.
  13. C

    1992 Evinrude 150hp EXEN will not run correctly

    backtrack a bit.... how did all this start suddenly ? any chance fuel is inadequate (contaminated) for some reason ? any chance the VRO is not working properly, is it getting good pulses from the crankcase to work under load at higher RPMS . smokes a lot ...oilsmoke ( bad mixing) or...
  14. C

    Lower unit oil

    me.... I prefer slotted because hex heads are easy to strip... never went back to hex heads Trying to remove s tripped he head is a real pia.
  15. C

    Evinrude 25202r no spark

    glad to help... saddly you are now addicted to repairing oldies....we all started with one and they keep showing up. Great hobby ....I fix them up with basic carb, ignition, gear oil and impeller and resell them at cost . keeps me busy in the winter :-) . it is a 25hp now find a small kicker...
  16. C

    1954 10 johnson rebuild

    best of both worlds 2 sets of points, 2 condensers, 2 coils 2 plugs :-)
  17. C

    1954 10 johnson rebuild

    I never went so far as to do rings on an oldy but have you looked into alternatives such as an engine cleaner like Merc POWER TUNE and BRP equivatents, pulled the cyl head to check/confirm excessive wear, checked the rings condition by openning the side bypass covers, ??
  18. C

    6hp johnson 6R -71E timing question

    gee billy glad you got it going ! forgot one word !! don't be worried about asking for help.
  19. C

    6hp johnson 6R -71E timing question

    gee billy glad you got going !
  20. C

    6hp johnson 6R -71E timing question

    just follow the video don't worry about the rest... incl. throttle position .
Top