Search results

  1. Scott Danforth

    Kill switch question

    Remove the lanyard for the normal contacts. The position the internal spring loaded contacts are at rest without the lanyard clip. Add the lanyard to hold the switch in the non-normal position My terminology is correct On a NCHO kill switch for magneto ignitions, the normal position is...
  2. Scott Danforth

    1957 Canadian Challenger rebuild

    Just an FYI. Many of us can not see facebook albums.
  3. Scott Danforth

    Tin boat prices

    VS Pulaski Wisconsin? https://www.google.com/maps/place/Pulaski,+WI+54162/@44.6673406,-88.2365464,
  4. Scott Danforth

    Cybertruck

    Here is my take...... the skin is low-grade 300 series stainless. most likely 302 or 304 (they just call it 300 series). bird droppings and falling leaves will leave staining just like DMC did on the delorean when they were launched with 304 and later switched to 316. Tesla is NOT using 316L...
  5. Scott Danforth

    Trailer tongue hinge

    Having owned factory folding tongues on various trailers, and looking at the retrofit tongues from companies like fulton with the small fasteners, or the weld-on version. I would replace the entire beam on the trailer with 3x3 or sleeve the 2.5 x 2.5 to get it up to 3.0 and use the weld-on kit...
  6. Scott Danforth

    Kill switch question

    the universal has both the NOHC (Normally Open, Held Closed) contacts and the NCHO (Normally Closed, Held Open) contacts the NOHC will have the purple wires for use on the powered ignitions. when you pull the lanyard, the switch reverts back to open, thus killing the ignition. the NCHO will...
  7. Scott Danforth

    Convert Bass tracker into a Catfish boat

    It will be cheaper to find the boat you want
  8. Scott Danforth

    Trailer tongue hinge

    I would weld it
  9. Scott Danforth

    Kill switch question

    Yes, get the universal kill switch and wire it.
  10. Scott Danforth

    Swivel seat mounts on bench seats?

    On the tinny fishing barge, the top wood in the aluminum seats is glued to the seat with 3M 4000 uv. The wood has 4 stainless T-nuts. The swivel bolts on top and the folding seat sits on top of that
  11. Scott Danforth

    Looking at 8hp and 15hp 4stroke Merc

    I usually just dropped on a lower pitch prop and idled the main motor when trolling. I could maintain 1.1 to 1.3mph trolling for walleye with the 15p, and ~2mph with the 17p
  12. Scott Danforth

    Have you had any dealings with the Yamaha website ? "https://yamaha2strokeoutboards.com/"

    they are non-US motors, and you wont ever see the motor and will be out your money transfer.
  13. Scott Danforth

    Mercruiser Alpha One, Gen 2 prop shaft rear seal r&r

    prop seals are always back-to-back seals. one seal keeps oil in. one seal is reversed to keep water out.
  14. Scott Danforth

    2003 wa cobia. Sleeper table

    make one. it looks like 3/4" starboard and there is a center post. the post most likely is a TACO post. https://tacomarine.com/table-pedestals-2 or a springfield post. https://springfieldgrp.com/products/tables/
  15. Scott Danforth

    3.0L Raw Water Intake & Drain Port Questions

    full system or half system? you have to know this and understand this prior to making any changes. half system: raw water comes in from drive, thru optional power steering cooler up to heat exchanger raw water inlet. raw water outlet is plumbed to manifold and exits. glycol inlet is plumbed...
  16. Scott Danforth

    BAYLINER VR5 SUNPAD 2020

    go to the bayliner dealer, have them order one from bayliner (will take about 12-20 weeks, or go to your local marine upholstery shop and have them make you one (will take about 6-8 weeks).
  17. Scott Danforth

    Herters 13.5 Needs a Motor

    No, the rating is based on length at waterline and transom width See 33CFR SS183.53 https://www.govinfo.gov/content/pkg/CFR-2002-title33-vol2/xml/CFR-2002-title33-vol2-sec183-53.xml
  18. Scott Danforth

    Annode location

    Direct contact with water
  19. Scott Danforth

    330 black scorpion low power

    If neutral safety switch malfunctions, and motor thinks it's in neutral, RPMs are limited to 3000 rpm
  20. Scott Danforth

    Herters 13.5 Needs a Motor

    https://www.fiberglassics.com/library/index.php?title=File:Hertersb56001.jpg Listed as 16 hp
Top