Search results

  1. Scott Danforth

    Staying warm on boat in the winter

    We used to go boating with temps in the 20's and 30s. Here is the rough rule of thumb 50s. Sweatshirt, wind breaker, sensible hat and gloves. May consider socks 40s. Jacket, heavy shirt. Heavy socks, good hat, gloves 30s. Snowmobile suit, or winter jacket and ski pants, heavy socks...
  2. Scott Danforth

    Volvo 4.3L Pre-Vortec to Vortec

    The 4.3 was a roller cam motor in 1988. The 1993-1995 motors are balance shaft motors. The 1996 and later just got the vortec heads. So the cheapest and easiest option for the OP is simply swap the heads and intake
  3. Scott Danforth

    Volvo 4.3L Pre-Vortec to Vortec

    I personally would pull your current motor, take it to a machine shop, rebuild the short block and just buy new vortec heads.
  4. Scott Danforth

    Volvo 4.3L Pre-Vortec to Vortec

    I would inspect your bores before spending money.
  5. Scott Danforth

    Volvo 4.3L Pre-Vortec to Vortec

    Get a vortec marine long block, or rebuild yours and add vortec heads. Bolt your stuff on it BTW, what do you mean by tons of hours? Most motors will go well over 4000 hours with maintenance Vortec heads good for 20-30hp on the 4.3
  6. Scott Danforth

    What Chevy engine is my 2006 350 MAG MPI Horizon?

    Wikipedia has more wrong information than a seloc or Haynes manual
  7. Scott Danforth

    1998 Regal 1700 LSR Advice

    I would be going thru the whole rig and do all the maintenance the prior owner didn't do.....like oil change, impeller change, bellows, alignment, and trailer bearings
  8. Scott Danforth

    1998 Regal 1700 LSR Advice

    here are some regal rebuilds on iboats. https://www.google.com/search?q=regal+transom+replacement+site%3Aiboats.com I agree with AD, finish the boating season, do some exploration.
  9. Scott Danforth

    1998 Regal 1700 LSR Advice

    see link in post #10. nearly all boats of the 80s and 90s and early 00's are built the same.
  10. Scott Danforth

    1998 Regal 1700 LSR Advice

    AD, what you see in the pic is the resin/glass/gel busted out as the wet wood underneath swelled up. that hunk of wood sits above the keel void. there is most likely water under the wood. having seen this on many rebuilds, its not a trivial thing.
  11. Scott Danforth

    1998 Regal 1700 LSR Advice

    Your boat uses wood as a core under the fiberglass. So to answer your question The transom (with fiberglass on both sides) The stringers (with fiberglass on all sides) The motor mounts (withe fiberglass) The deck (with fiberglass on both sides) Read this to understand boat construction...
  12. Scott Danforth

    Drain process

    youre trying to drain your motors in an express cruiser while in the water? the water will stop flowing once the boat sinks. seriously, your engine blocks are below the waterline.
  13. Scott Danforth

    Starter

    the model number comes up as 1989 Ford 5.0 (as Lou indicated) the OMC part number is NLA. however simply take your starter to your local starter and alternator shop and they can rebuild it.
  14. Scott Danforth

    1998 Regal 1700 LSR Advice

    first, welcome aboard. second, the second pic show some concerning issues as that damage only comes from wet core material that freezes. Wet wood means that is is starting to rot (and will not dry out) Hammer test means nothing. I would start planning a hull restoration. 4th sticky down at...
  15. Scott Danforth

    What Chevy engine is my 2006 350 MAG MPI Horizon?

    post #5 has the information you need.
  16. Scott Danforth

    1999 Chris Craft 210 bowrider

    Did you call Chris Craft? Or search ebay or any of the NOS marine surplus sites?
  17. Scott Danforth

    2023 Splash of the Year Nominations!

    Hey @mickyryan or @kcassells .... You guys splash yet?
  18. Scott Danforth

    Tire Recommendation, Japanese Sedan

    FWIW.....I rotate tires to burn them off evenly. The fronts scrub the outside edges and the rears see a bit of slip now and then. I could get another 5-8 thousand.... However that's not as fun
  19. Scott Danforth

    48 years...

    FWIW, my buds boat does 18mph with a 30hp. I would think with the correct height and correct prop you should be closer to 30
  20. Scott Danforth

    What Chevy engine is my 2006 350 MAG MPI Horizon?

    All SBCs with vortec heads have 8 bolts per intake (4 bolts per head). Including the 1988 SBC I warmed over. Stop thinking the marine/industrial motor is same as an automotive offering
Top